background image

 

Operation

 

31

 

from the fuel tank.

4.

Squeeze the primer pump, with the ar-
row pointing up, until you feel it become
firm.

 

EMU27491

 

Starting engine

WARNING

 

EWM01600 

 

Before starting the engine, make sure
that the boat is tightly moored and that
you can steer clear of any obstructions.
Be sure there are no swimmers in the wa-

 

ter near you.

 

EMU27543

 

Starting engine

 

1.

Place the gear shift lever in neutral.

NOTE:

 

The start-in-gear protection device prevents

the engine from starting except when in neu-

 

tral.

2.

Attach the engine shut-off cord to a se-
cure place on your clothing, or your arm
or leg. Then install the clip on the other
end of the cord into the engine shut-off
switch.

WARNING

 

EWM00121 

 

 

Attach the engine shut-off cord to a se-
cure place on your clothing, or your
arm or leg while operating.

 

 

Do not attach the cord to clothing that
could tear loose. Do not route the cord
where it could become entangled, pre-
venting it from functioning.

 

 

Avoid accidentally pulling the cord dur-
ing normal operation. Loss of engine
power means the loss of most steering
control. Also, without engine power,
the boat could slow rapidly. This could
cause people and objects in the boat to

 

be thrown forward.

 

3.

Place the throttle grip in the “

(start) position.

 

1. Arrow

ZMU05533

N

ZMU02026

Summary of Contents for F13.5B



























































































Reviews: