Yamaha F13.5B Page 20 Owner'S Manual Download | Manualshive

Page: 20 / 90

background image

Basic components

14

fuel tank, its function is as follows.

WARNING

EWM00020

The fuel tank supplied with this engine is
its dedicated fuel reservoir and must not
be used as a fuel storage container. Com-
mercial users should conform to relevant
licensing or approval authority regula-

tions.

EMU25830

Fuel joint

This joint is used to connect the fuel line.

EMU25841

Fuel gauge

This gauge is located on either the fuel tank
cap or on the fuel joint base. It shows the ap-
proximate amount of fuel remaining in the
tank.

EMU25850

Fuel tank cap

This cap seals the fuel tank. When removed,
the tank can be filled with fuel. To remove the
cap, turn it counterclockwise.

EMU25860

Air vent screw

This screw is on the fuel tank cap. To loosen
the screw, turn it counterclockwise.

EMU26180

Remote control

The remote control lever actuates both the
shifter and the throttle. The electrical switch-
es are mounted on the remote control box.

1. Fuel joint
2. Fuel gauge
3. Fuel tank cap
4. Air vent screw

1. Power tilt switch
2. Remote control lever
3. Neutral interlock trigger
4. Neutral throttle lever
5. Main switch / choke switch
6. Engine shut-off switch
7. Throttle friction adjuster

1. Remote control lever
2. Neutral interlock trigger
3. Neutral throttle lever
4. Main switch / choke switch
5. Engine shut-off switch
6. Throttle friction adjuster

1

2

3

4

5

6

ZMU04862

«
...
18
19
20
21
22
...
»

Summary of Contents for F13.5B



























































































Reviews:

No comments

Related manuals for F13.5B

Brand: Navia Pages: 26

Brand: Rosch Computer Pages: 87

Brand: AOpen Pages: 8

Brand: Aaeon Pages: 97

STEVAL-IME008V1

Brand: STMicroelectronics Pages: 19

Brand: Yamaha Pages: 223

IMBA-BDE-1518-R10

Brand: IEI Technology Pages: 14

Brand: Avalue Technology Pages: 116

Brand: Epcom Pages: 8

Brand: Biostar Pages: 63

Brand: Renesas Pages: 30

Brand: ICP Pages: 50

CS631-C246/Q370

Brand: DFI Pages: 79

X58 Classified3

Brand: EVGA Pages: 2

NuMaker NUC980 IIoT

Brand: Nuvoton Pages: 46

Brand: Gigabyte Pages: 39

Brand: Advantech Pages: 98

Brand: JETWAY Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands