Yamaha F13.5B Owner'S Manual Download

Page: 63 / 90

Maintenance

EMU34431

Maintenance chart 1

Frequency of maintenance operations may be adjusted according to the operating condi-
tions, but the following table gives general guidelines. Refer to the sections in this chapter for
explanations of each owner-specific action.

NOTE:

When operating in salt water, muddy, other turbid (cloudy), acidic water, the engine should

be flushed with clean water after each use.

The “

” symbol indicates the check-ups which you may carry out yourself.

The “

” symbol indicates work to be carried out by your Yamaha dealer.

Item

Actions

Initial

Every

20 hours

months)

100

hours (1

years)

300

hours (3

years)

500

hours (5

years)

Anode(s) (external)

Inspection or replace-
ment as necessary

Anode(s) (cylinder
head, thermostat
cover)

Inspection or replace-
ment as necessary

Anodes (exhaust cover,
cooling water passage
cover, Rectifier Regula-
tor cover)

Replacement

Anode(s) (exhaust
cover, cover joint)

Replacement

Battery

Inspection or charging,
replacement as neces-
sary

Cooling water leakage

Inspection or replace-
ment as necessary

Cowling clamp

Inspection

Engine starting condi-
tion/Noise

Inspection

Engine idling speed/
Noise

Inspection

Engine oil

Replacement

Engine Oil filter (car-
tridge)

Replacement

Fuel filter (can be dis-
assembled)

Inspection or replace-
ment as necessary

Fuel pump

Inspection or replace-
ment as necessary

Fuel/oil leakage

Inspection

Summary of Contents for F13.5B



























































































Search results

Summary of Contents for F13.5B

Reviews:

Related manuals for F13.5B

Brands by name

Popular brands

Yamaha F13.5B, Owner'S Manual

Search results

Summary of Contents for F13.5B

Reviews:

Related manuals for F13.5B

Brands by name

Popular brands