manualshive.com logo in svg

Yamaha Electone F-15, Owner'S Manual

Share
Download
Yamaha Electone F-15 Owner'S Manual Download Page 74

Maintenance

68

7. When transporting or storing the out-

board motor while removed from a boat,
keep the outboard motor in the attitude
shown.

TIP:

Place a towel or something similar under the
outboard motor to protect it from damage.

EMU28242

Storing outboard motor

When storing your Yamaha outboard motor
for prolonged periods of time (2 months or
longer), several important procedures must
be performed to prevent excessive damage.
It is advisable to have your outboard motor
serviced by an authorized Yamaha dealer
prior to storage. However, you, the owner,
with a minimum of tools, can perform the fol-
lowing procedures.

NOTICE

ECM01081

To prevent problems which can be
caused by oil entering the cylinder from
the sump, keep the outboard motor in
the attitude shown when transporting
and storing it. If storing or transporting
the outboard motor on its side (not up-

1. Steering bracket
2. Handgrip

ZMU05633

1

1

2

2

ZMU05634

ZMU05630

6AG-9-3D-1E0.book  68 ページ  ２０１５年１１月５日　木曜日　午前１１時７分

Summary of Contents for Electone F-15















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands