manualshive.com logo in svg

Yamaha Electone F-15, Owner'S Manual

Share
Download
Yamaha Electone F-15 Owner'S Manual Download Page 64

Operation

58

EMU27873

Adjusting trim angle for manual tilt 
models

There are 4 or 5 holes provided in the clamp
bracket to adjust the outboard motor trim an-
gle.
1. Stop the engine.
2. Tilt the outboard motor up, and then re-

move the trim rod from the clamp brack-
et.

3. Reposition the rod in the desired hole.
To raise the bow (“trim-out”), move the rod
away from the transom.
To lower the bow (“trim-in”), move the rod to-
ward the transom.
Make test runs with the trim set to different
angles to find the position that works best for
your boat and operating conditions.

WARNING

EWM00401

Stop the engine before adjusting the
trim angle.

Use care to avoid being pinched when
removing or installing the rod.

Use caution when trying a trim position
for the first time. Increase speed gradu-
ally and watch for any signs of instabil-
ity or control problems. Improper trim
angle can cause loss of control.

TIP:

The outboard motor trim angle can be
changed approximately 4 degrees by shifting
the trim rod one hole.

EMU27906

Adjusting trim angle (power tilt 
models)

WARNING

EWM00754

Be sure all people are clear of the out-
board motor when adjusting the trim
angle. Body parts can be crushed be-
tween the motor and the clamp bracket
when the motor is trimmed or tilted.

Use caution when trying a trim position
for the first time. Increase speed gradu-
ally and watch for any signs of instabil-
ity or control problems. Improper trim
angle can cause loss of control.

If equipped with a power trim and tilt
switch located on the bottom cowling,
use the switch only when the boat is at
a complete stop with the engine off. Do
not adjust the trim angle with this
switch while the boat is moving.

1. Move the gear shift lever to the neutral

position.

TIP:

While the boat is moving, it may be difficult to
adjust the trim angle due to water pressure.
Before adjusting the trim angle, reduce the
boat speed and shift into neutral.
2. Tilt the outboard motor to the desired an-

gle using the power tilt switch.

1. Trim rod

ZMU05601

1

6AG-9-3D-1E0.book  58 ページ  ２０１５年１１月５日　木曜日　午前１１時７分

Summary of Contents for Electone F-15















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands