manualshive.com logo in svg

Yamaha Electone F-15, Owner'S Manual

Share
Download
Yamaha Electone F-15 Owner'S Manual Download Page 52

Operation

46

Securely moor the boat in a well-ventilated
area and stop the engine. If the boat is
trailered, ensure it is stable.

Do not smoke and keep away from sparks,
flames, static electric discharges, or other
sources of ignition.

If you use a portable container to store and
dispense fuel, use only a locally approved
GASOLINE container.

To prevent electrostatic sparks, discharge
any built-up static electricity from your
body before refueling.

1. Disconnect the fuel hose from the fuel

joint on the fuel tank.

2. Turn the air vent screw clockwise to

close it.

3. Remove the fuel tank from the boat.
4. To loosen the air vent screw, turn it

counterclockwise until it stops.

5. While pressing and holding the pressure

relief tab under the fuel tank cap, slowly
turn the fuel tank cap counterclockwise
1/4 turn.

TIP:

Release the fuel vapor contained in the fuel
tank.
6. While pressing and holding the pressure

relief tab under the fuel tank cap again,
turn the fuel tank cap counterclockwise
to remove it.

1. Fuel joint
2. Fuel hose

1. Air vent screw

ZMU07443

2

1

1

ZMU07444

1. Air vent screw

1. Pressure relief tab
2. Fuel tank cap

1

ZMU07445

1

2

ZMU07446

6AG-9-3D-1E0.book  46 ページ  ２０１５年１１月５日　木曜日　午前１１時７分

Summary of Contents for Electone F-15















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands