manualshive.com logo in svg

Yamaha Disklavier E3 Series, Maintenance Handbook

Share
Download
Yamaha Disklavier E3 Series Maintenance Handbook Download Page 34

 19 

    6-2. MC SHEET TEST 
                                                     
 
 
 
 
                                                     
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

=TEST MODE= 

 MC SHEET 
               (↓,↑,→) 

 

 

 (1) MC SHEET Version 
 Ver 0.2.0 

  
 (2) SDRAM Read Test 
     Push PLAY Key

 

 

 (3) FLASH R/W Test  
     Push PLAY Key

 

 

 (4) FLASH Read Test 
     Push PLAY Key

  
 (5) DIGITAL I/O Test 
     Push PLAY Key

  
 (6) CD-ROM Read Test 
     Push PLAY Key

  
 (7) USB Read Test 
     Push PLAY Key

  
 (8) NAND Read Test 
     Push PLAY Key    

  
 (9) ETHERNET Test 
     Push PLAY Key    

 
 (2) SDRAM Read Test 
        OK !

 

 (3) FLASH R/W Test  
        OK !

 

 (4) FLASH Read Test 
        OK !

 
 (5) DIGITAL I/O Test 
        OK !

 
 (6) CD-ROM Read Test 
        OK !

 
 (7) USB Read Test 
        OK !

 
 (8) NAND Read Test 
        OK !

 
 (9) ETHERNET Test 
     OK !  00A0DE:4D****

←

 

→

 

Displays the version number of MC sheet. 

Insert a CD-ROM to the CD drive. 
Press [PLAY/PAUSE] button. 

Insert a USB memory to the [USB TO 
DEVICE] port. And press [PLAY/PAUSE] 
button. 

Connect the LAN. Press the [PLAY/PAUSE] button. 
MAC address should be displayed in the lower light. 
Check that it starts with “00A0DE:4D”. 
 

NAND Flash memory test. 

32 

Summary of Contents for Disklavier E3 Series





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands