Yamaha Digital Sound Projector HTY-750 Owner'S Manual Download Page 98

Page: 98 / 98

Press ENTER to start the AUTO
SETUP procedure, and then

leave the room within 10 seconds.

The following screen appears on the TV. Leave the room
within 10 seconds before the AUTO SETUP procedure
starts.

The setup screen automatically changes during the AUTO
SETUP procedure.

When the AUTO SETUP procedure is completed, the
following screen appears on the TV.

If “ENVIRONMENT CHECK (FAILED) is displayed, see page
36 in the Owner’s Manual and then run the procedure again.

Hint

• The result may differ depending on the environment.
• If any error occurs, the corresponding error message appears

on the screen. In this case, see “Error messages for AUTO
SETUP” on page 37 in the Owner’s Manual and then follow
the instructions. To start the AUTO SETUP procedure once
again, press RETURN.

Press ENTER.

The following screen appears on the TV for 2 seconds and
then the menu screen disappears from the TV.

Disconnect the IntelliBeam

microphone.

The AUTO SETUP has completed. Keep the IntelliBeam
microphone in a safe place.
The settings are automatically saved in the system memory.

Enjoy TV or DVD digital audio in surround sound.

For instructions on how to operate or set your TV or DVD player, refer to the owner’s manual supplied with each component.

Enjoying surround sound

Carry out the AUTO SETUP to adjust the settings that best match your
listening environment

The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment.

It is normal for loud test tones to be output

during the AUTO SETUP procedure.

Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress.

Press STANDBY/ON on the

remote control.

The power of this unit turns on.
Before operations, insert batteries into the remote control
(see page 26 in the Owner’s Manual).
If necessary, adjust the volume level of this unit.
If you have connected the subwoofer, set the volume and
crossover/high cut frequency. Refer to the note on page
32 in the Owner’s Manual.

Check the multi-channel digital signal being output at this unit.

The MULTI indicator and/or (see page 42 in the Owner’s Manual) is lit in the front panel display.

If the sound is

output from your TV speakers, mute the volume on your TV.

For details about digital audio input signals, see

page 46 in the Owner’s Manual.

Press /- on the remote control to adjust the volume
level of this unit.

Press one of the beam mode buttons on the remote control

to select the desired beam mode.

Select one of the six beam modes that best matches the current input source of this unit.
For further information on the beam modes, see page 44 in the Owner’s Manual.

To fine-tune the listening environment parameters manually or make advanced settings for speaker positions,

sound beams, etc., see “MANUAL SETUP” on page 56 in the Owner’s Manual.

AUTO SETUP START

Will begin in 10sec

Please leave the room

**--------

[RETURN]:Cancel

Enjoying TV in surround sound

SHOW RESULT

MEASUREMENT COMPLETE

BEAM MODE :5 BEAM
SUBWOOFER :NOT APPLICABLE

[ENTER]:Save set-up

[RETURN]:Do not save set-up

AUTO SETUP COMPLETE

Please remove the MIC from
the YSP and the listening
position.

CH LEVEL

MENU

RETURN

TEST

YSP

TV/AV

ENTER

CH LEVEL

MENU

RETURN

TEST

YSP

TV/AV

ENTER

Select the TV channel using the
remote control supplied with

your TV.

Set the operation mode selector

to YSP.

This unit switches to the YSP operation mode.

Press TV on the remote control
of this unit.

This unit switches to the TV playback mode.

More than 1.8 m (6.0 ft)

Within 1 m
(3.3 ft)

IntelliBeam

microphone

Cardboard

microphone

stand

Listening

position

Place the IntelliBeam microphone on
the extended center line of this unit
and 1.8 m (6.0 ft) or more away from
it. Also, make sure place the
IntelliBeam microphone within 1 m
(3.3 ft) upper or lower from the center
height of this unit.

IntelliBeam
microphone

Center line

Carry out the AUTO SETUP (IntelliBeam)

INTELLIBEAM MIC

INPUT

VOLUME

STANDBY/ON

INTELLIBEAM MIC

Set the IntelliBeam microphone at your normal listening position.

Use the supplied cardboard microphone stand or a tripod to

place the IntelliBeam microphone at the same height as your ears would

be when you are seated.

IntelliBeam microphone (supplied)

Connect the supplied IntelliBeam microphone to the INTELLIBEAM MIC

jack on the front panel.

You may want to use the supplied cardboard microphone stand for the AUTO SETUP. Assemble the stand and place the IntelliBeam
microphone on top of it as shown below.

TV VOL

VOLUME

MUTE

TV INPUT

TV MUTE

Enjoying DVDs in surround sound

Select the DVD video input on

your TV.

Set the operation mode selector

to YSP.

This unit switches to the YSP operation mode.

1) Press DVD on the remote

control of this unit.

This unit switches to the DVD playback mode.

2) Play back

the supplied demonstration

DVD

on the DVD player.

Set the operation mode selector
to YSP.

This unit switches to the YSP (Yamaha HTY-750 Digital
Sound Projector) operation mode.

Press and hold AUTO SETUP for

more than 2 seconds.

The menu screen appears on the TV.
If the menu screen does not appear, check the OSD video
pin cable (see the connection example on the front page).

Check the following points.

About the IntelliBeam microphone

• Is the microphone placed on an imaginary center line drawn

from this unit?

• Is the microphone placed within 1 m (3.3 ft) upper or lower

from the center height of this unit?

• Is the microphone placed more than 1.8 m (6.0 ft) from the

front of this unit?

About the room environment

• Is your listening room kept as quiet as possible?

Prepare to leave the room.

The best setting may not be done if you are in the room.

Prepare to leave the room in 10 seconds after pressing
ENTER in step 10.

Hint

• When leaving the room, bring this guide with you.
• Wait outside the room during the AUTO SETUP procedure.
• The AUTO SETUP procedure takes

about 3 minutes.

• To cancel the AUTO SETUP procedure after it is started,

press RETURN.

Turn on the power of your TV.

Select the appropriate video
input on your TV.

“HTY-750” appears on your TV. If the OSD video pin cable
is connected to the video input 1 on the TV as shown in the
connection example, switch the video input to “1”.

Within 1 m
(3.3 ft)

CH LEVEL

MENU

RETURN

TEST

YSP

TV/AV

ENTER

AUTO SETUP

PREPARATION & CHECK

Please connect the MIC.
Please place the MIC at least
1.8m/6ft away from the YSP
unit. The MIC should be set
at ear level when seated.

After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel