Yamaha CRW4261t-NB User Manual Download Page 22

Page: 22 / 25

Troubleshooting

If CRW4261t is not performing as expected, look up the symptoms in the following table,

and take the appropriate corrective action.

Symptoms

Corrective action

The power to the CRW4261t is off

• Check the DC power cable connection.

The CRW4261t is not recognized by

the computer

• Check the IDE interface connector connection.

• Is the MASTER/SLAVE setting correct?

• If there is only one device connected to the IDE

interface connector, is it connected to the end of

the connector?

The disc tray will not open

• Make sure that the power to the drive is turned

on.

The disc ejects

• Make sure that the disc is seated in the tray cor-

rectly.

Incorrect operation

• Make sure that the disc is seated in the tray cor-

rectly.

• Make sure that you are using the correct disc.

• Make sure that there is no dust, dirt, or conden-

sation on the disc or tray.

Summary of Contents for CRW4261t-NB


























Search results

Summary of Contents for CRW4261t-NB

Reviews:

Related manuals for CRW4261t-NB

Brands by name

Popular brands

Yamaha CRW4261t-NB, User Manual

Search results

Summary of Contents for CRW4261t-NB

Reviews:

Related manuals for CRW4261t-NB

Brands by name

Popular brands