Yamaha CRW4261t-NB User Manual Download Page 17 | Manualshive

Page: 17 / 25

background image

Chapter 2 - Installing the Yamaha CRW4261t Drive

11

9. Tighten the four fastening screws securely.

10. Attach the cover of your computer.

11. Connect the power cable to an AC outlet, and switch on

your computer.

Make sure that the LED located on the panel of the CRW4261t drive is lit.

12. Start up your operating system.

For the procedure, refer to the manual for your operation system.

13. Install the writing software.

For the installation procedure, refer to the manual for your writing soft-

ware.

«
...
15
16
17
18
19
...
»

Summary of Contents for CRW4261t-NB


























Reviews:

No comments

Related manuals for CRW4261t-NB

Relion 670 series

Brand: ABB Pages: 66

Brand: Xoop Lighting Pages: 20

Brand: Vari Lite Pages: 132

Brand: Zenbooth Pages: 60

Brand: Parker Research Corp Pages: 4

Brand: Eastwood Pages: 20

Brand: Daihan Scientific Pages: 43

Brand: Daga Pages: 24

Brand: DAF Pages: 68

Brand: Haaga Pages: 31

Brand: Tactile Medical Pages: 23

Brand: Taarup Pages: 72

Brand: GE Pages: 176

Brand: Triton Blue Pages: 11

Brand: Ideal Heating Pages: 16

Brand: Onwa Pages: 35

Brand: York International Pages: 16

Brand: X-10 Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands