background image

 

Maintenance

 

54

 

7.

Activate the trim-up switch until the tilt
rod is fully extended. Unlock the tilt sup-
port lever.

8.

Tilt the outboard motor down. Check
that the tilt rod and trim rods operate
smoothly.

NOTE:

 

Consult your Yamaha dealer if any operation

 

is abnormal.

 

EMU29171

 

Checking propeller

WARNING

 

EWM00321 

 

You could be seriously injured if the en-
gine accidentally starts when you are
near the propeller.

 

 

Before inspecting, removing, or install-
ing the propeller, remove the spark
plug caps from the spark plugs. Also,
place the shift control in neutral, turn
the main switch to “

” (off) and re-

move the key, and remove the lanyard
from the engine stop switch. Turn off
the battery cut-off switch if your boat
has one.

 

 

Do not use your hand to hold the pro-
peller when loosening or tightening the
propeller nut. Put a wood block be-
tween the anti-cavitation plate and the
propeller to prevent the propeller from

 

turning.

 

Checkpoints

 

 

Check each of the propeller blades for
wear, erosion from cavitation or ventila-
tion, or other damage.

 

 

Check the propeller shaft for damage.

 

 

Check the splines / shear pin for wear or
damage.

 

 

Check for fish line tangled around the pro-
peller shaft.

ZMU03884

ZMU01896

ZMU01897

©

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for 90




















































































Reviews: