Yamaha 90 Owner'S Manual Download Page 53

Page: 53 / 83

Maintenance

EMU28522

Maintenance chart

Frequency of maintenance operations may be adjusted according to the operating condi-
tions, but the following table gives general guidelines. Refer to the sections in this chapter for
explanations of each owner-specific action.

NOTE:

When operating in salt water, turbid or muddy water, the engine should be flushed with clean

water after each use.

The “

” symbol indicates the check-ups which you may carry out yourself.

The “

” symbol indicates work to be carried out by your Yamaha dealer.

Item

Actions

Initial

Every

10 hours

(1 month)

50 hours

months)

100

hours (6
months)

200

hours (1

year)

Anode(s) (external)

Inspection / replace-
ment

Anode(s) (internal)

Inspection / replace-
ment

Battery

Inspection / charging

Cooling water pas-
sages

Cleaning

Cowling clamp

Inspection

Fuel filter (can be dis-
assembled)

Inspection / cleaning

Fuel system

Inspection

Fuel tank (Yamaha por-
table tank)

Inspection / cleaning

Gear oil

Change

Greasing points

Greasing

Idling speed (carbure-
tor models)

Inspection

PCV (Pressure Con-
trol Valve)

Inspection

Power trim and tilt unit

Inspection

Propeller and cotter pin

Inspection / replace-
ment

Shift link / shift cable

Inspection / adjustment

Thermostat

Inspection / replace-
ment

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for 90




















































































Search results

Summary of Contents for 90

Reviews:

Related manuals for 90

Brands by name

Popular brands

Yamaha 90, Owner'S Manual

Search results

Summary of Contents for 90

Reviews:

Related manuals for 90

Brands by name

Popular brands