background image

 

Operation

 

36

 

To raise the bow (trim-out), press the switch

” (up).

To lower the bow (trim-in), press the switch

” (down).

Make test runs with the trim set to different
angles to find the position that works best for
your boat and operating conditions.

NOTE:

 

To adjust the trim angle while the boat is
moving, use the power trim and tilt switch lo-
cated on the remote control device or tiller

 

handle, if equipped.

 

EMU27911

 

Adjusting boat trim

 

When the boat is on plane, a bow-up attitude
results in less drag, greater stability and effi-
ciency. This is generally when the keel line of
the boat is up about 3 to 5 degrees. With the
bow up, the boat may have a greater tenden-
cy to steer to one side or the other. Compen-
sate for this as you steer. The trim tab can
also be adjusted to help offset this effect.
When the bow of the boat is down, it is easier
to accelerate from a standing start onto
plane.

 

Bow Up

 

Too much trim-out puts the bow of the boat
too high in the water. Performance and econ-
omy are decreased because the hull of the
boat is pushing the water and there is more
air drag. Excessive trim-out can also cause
the propeller to ventilate, which reduces per-
formance further, and the boat may “por-
poise” (hop in the water), which could throw
the operator and passengers overboard.

 

Bow Down

 

Too much trim-in causes the boat to “plow”
through the water, decreasing fuel economy
and making it hard to increase speed. Oper-
ating with excessive trim-in at higher speeds
also makes the boat unstable. Resistance at
the bow is greatly increased, heightening the
danger of “bow steering” and making opera-
tion difficult and dangerous.

 

1. Power trim and tilt switch

©

2019 Yamaha Motor Corporation, U.S.A.

Summary of Contents for 90




















































































Reviews: