Yamaha 9.9D Owner'S Manual Download Page 3 | Manualshive

Page: 3 / 64

background image

Important manual information

EMU25100

To the owner

Thank you for choosing a Yamaha outboard
motor. This Owner’s Manual contains infor-
mation needed for proper operation, mainte-
nance and care. A thorough understanding of
these simple instructions will help you obtain
maximum enjoyment from your new Yamaha.
If you have any question about the operation
or maintenance of your outboard motor,
please consult a Yamaha dealer.
In this Owner’s Manual particularly important
information is distinguished in the following
ways.

The Safety Alert Symbol means AT-

TENTION! BECOME ALERT! YOUR SAFE-
TY IS INVOLVED!

WARNING

EWM00780

Failure to follow WARNING instructions
could result in severe injury or death to the
machine operator, a bystander, or a per-
son inspecting or repairing the outboard
motor.

CAUTION:

ECM00700

A CAUTION indicates special precautions
that must be taken to avoid damage to the
outboard motor.

NOTE:

A NOTE provides key information to make
procedures easier or clearer.

Yamaha continually seeks advancements in
product design and quality. Therefore, while
this manual contains the most current product
information available at the time of printing,
there may be minor discrepancies between

your machine and this manual. If there is any
question concerning this manual, please con-
sult your Yamaha dealer.

NOTE:

The 9.9MH, 15MH and the standard accesso-
ries are used as a base for the explanations
and illustrations in this manual. Therefore
some items may not apply to every model.

EMU25110

9.9D, 15D

OWNER’S MANUAL

©2004 by Yamaha Motor Corporation,

USA

1st edition, February 2004

All rights reserved.

Any reprinting or unauthorized use

without the written permission of

Yamaha Motor Corporation, USA

is expressly prohibited.

Printed in Japan

P/N LIT-18626-05-82

U63V17E0.book Page 1 Thursday, February 26, 2004 11:52 AM

«
1
2
3
4
5
...
»

Summary of Contents for 9.9D

































































Reviews:

No comments

Related manuals for 9.9D

Brand: Yamaha Pages: 76

Brand: Gigabyte Pages: 74

Brand: R&S Pages: 44

GA-AX370M-Gaming 3

Brand: Gigabyte Pages: 40

Brand: Supero Pages: 90

Brand: Intel Pages: 12

A20-OLINUXINO-LIME

Brand: OLIMEX Pages: 49

EVAL-IH-R5IPB-A-V1

Brand: Infineon Pages: 34

i.MX 8M Mini SODIMM SOM

Brand: iWave Pages: 16

Brand: Xilinx Pages: 40

TIM-UP-19kS3-Spartan6

Brand: Bluetechnix Pages: 19

Brand: ASROCK Pages: 151

Brand: ASROCK Pages: 103

X299 Killer SLI/ac

Brand: ASROCK Pages: 198

Brand: Octagon Pages: 153

Brand: Abit Pages: 88

Brand: Abit Pages: 104

Brand: Boston Scientific Pages: 202

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands