Yamaha 9.9D Owner'S Manual Download Page 29 | Manualshive

Page: 29 / 64

background image

Operation

24

EMU27740

Shifting

WARNING

EWM00180

Before shifting, make sure there are no
swimmers or obstacles in the water near
you.

CAUTION:

ECM00220

To change the boat direction or shifting
position from forward to reverse or vice-
versa, first close the throttle so that the en-
gine idles (or runs at low speeds).

EMU27763

Forward (tiller handle and remote
control models)

Tiller control models
1.

Place the throttle grip in the fully closed
position.

2.

Move the gear shift lever quickly and firm-
ly from neutral to forward.

Remote control models
Pull up the neutral interlock trigger (if
equipped) and move the remote control lever
quickly and firmly from neutral to forward.

EMU27795

Reverse (manual tilt and hydro tilt
models)

WARNING

EWM00190

When operating in reverse, go slowly. Do
not open the throttle more than half. Other-
wise the boat could become unstable,
which could result in loss of control and
an accident.

Tiller control models
1.

Place the throttle grip in the fully closed
position.

2.

On models equipped with a tilt lock lever,
check that it is in the lock/down position.

ZMU02856

ZMU02030

ZMU02030

U63V17E0.book Page 24 Thursday, February 26, 2004 11:52 AM

«
...
27
28
29
30
31
...
»

Summary of Contents for 9.9D

































































Reviews:

No comments

Related manuals for 9.9D

Cyclone IV GX FPGA

Brand: Altera Pages: 60

Brand: AOpen Pages: 8

Brand: Abit Pages: 48

Brand: Zida Pages: 28

Brand: ECS Pages: 52

Brand: Gigabyte Pages: 80

Brand: Supermicro Pages: 124

Brand: Advantech Pages: 4

Brand: Supero Pages: 105

Brand: ST Pages: 11

GF7100P-M7 - BIOS SETUP

Brand: Biostar Pages: 45

NuMicro NuTiny-SDK-NUC505

Brand: Nuvoton Pages: 26

Brand: BCM Advanced Research Pages: 9

Brand: DFI Pages: 38

Brand: Asus Pages: 50

Brand: Asus Pages: 58

Brand: Asus Pages: 92

Brand: Asus Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands