Yamaha 9.9D Owner'S Manual Download Page 36 | Manualshive

Page: 36 / 64

background image

Operation

31

5.

Slightly tilt the outboard motor up until the
tilt support bar automatically returns to
the free position.

6.

Slowly lower the outboard motor to the
normal position.

EMU28190

Cruising in other conditions

Cruising in salt water

After operating in salt water, wash out the
cooling water passages with fresh water to
prevent them from becoming clogged with salt
deposits.

NOTE:

For cooling system flushing instructions, see
page 32.

Cruising in turbid water

Yamaha strongly recommends that you use
the optional chromium-plated water pump kit
if you use the outboard motor in turbid (mud-
dy) water conditions.

ZMU02048

U63V17E0.book Page 31 Thursday, February 26, 2004 11:52 AM

«
...
34
35
36
37
38
...
»

Summary of Contents for 9.9D

































































Reviews:

No comments

Related manuals for 9.9D

Brand: P&E Microcomputer Systems Pages: 59

Brand: Yamaha Pages: 86

ASC Bridge Board

Brand: Lattice Semiconductor Pages: 25

EZ-USB HX2LP CY4605

Brand: Cypress Pages: 2

Brand: Beagleboard.org Pages: 2

Brand: Texas Instruments Pages: 18

Brand: ASROCK Rack Pages: 93

Brand: Intel Pages: 12

Brand: Atmel Pages: 30

Brand: NXP Semiconductors Pages: 12

Brand: Intel Pages: 92

Brand: ON Semiconductor Pages: 8

Brand: TESSERA Pages: 31

Brand: Texas Instruments Pages: 13

Brand: MSI Pages: 148

z75a-g45 series

Brand: MSI Pages: 88

Brand: Suzuki Pages: 336

Brand: SOYO Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands