Yamaha 60 Owner'S Manual Download | Manualshive

Page: 70 / 82

background image

Trouble Recovery

65

engine is running. Do not install the
starter mechanism or top cowling after
the engine is running.

●

Do not touch the ignition coil, spark
plug wire, spark plug cap, or other elec-
trical components when starting or op-
erating the motor. You could get an

electrical shock.

EMU29573

Emergency starting engine

1.

Remove the top cowling.

2.

Disconnect the start-in-gear protection
cable from the starter, if equipped.

3.

Remove the starter/flywheel cover after
removing the bolt(s).

4.

Prepare the engine for starting. For fur-
ther information, see page 29. Be sure
the engine is in neutral and that the en-
gine stop switch lanyard lock plate is at-
tached to the engine stop switch. The
main switch must be “

” (on), if

equipped.

5.

Insert the knotted end of the emergency
starter rope into the notch in the flywheel
rotor and wind the rope several turns
around the flywheel clockwise.

6.

Pull the rope slowly until resistance is
felt.

7.

Give a strong pull straight out to crank
and start the engine. Repeat if neces-
sary.

ZMU02609

OFF

ZMU03541

ON

ZMU02614

«
...
68
69
70
71
72
...
»

Summary of Contents for 60



















































































Reviews:

No comments

Related manuals for 60

Brand: Yamaha Pages: 82

Brand: Yamaha Pages: 90

Brand: JETWAY Pages: 44

Brand: Navia Pages: 26

MBATX-845GV-VEAH

Brand: Kontron Pages: 70

Brand: JETWAY Pages: 44

Brand: Aaeon Pages: 44

Brand: JETWAY Pages: 49

Brand: Biostar Pages: 65

Brand: Nuvoton Pages: 14

Brand: ON Semiconductor Pages: 19

Brand: EPOX Pages: 84

Brand: IEI Technology Pages: 160

Brand: C&T Solution Pages: 65

Brand: Gigabyte Pages: 40

Brand: Intel Pages: 76

Brand: AOpen Pages: 44

Brand: JETWAY Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands