Yamaha 60 Owner'S Manual Download

Page: 44 / 82

Operation

from marine growth and corrosion which
could damage the power trim and tilt

mechanism.

EMU28053

Procedure for tilting down

Power trim and tilt models / power tilt models
1.

Push the power tilt / power trim and tilt
switch “

” (up) until the outboard motor

is supported by the tilt rod and the tilt
support lever / tilt support knob becomes
free.

Release the tilt support lever or pull out
the tilt support knob.

Push the power tilt / power trim and tilt
switch “

” (down) to lower the outboard

motor to the desired position.

EMU28060

Cruising in shallow water

The outboard motor can be tilted up partially
to allow operation in shallow water.

EMU28090

Power trim and tilt models / power tilt
models

The outboard motor can be tilted up partially

ZMU02546

ZMU02569

ZMU01936

ZMU03838

Summary of Contents for 60



















































































Search results

Summary of Contents for 60

Reviews:

Related manuals for 60

Brands by name

Popular brands

Yamaha 60, Owner'S Manual

Search results

Summary of Contents for 60

Reviews:

Related manuals for 60

Brands by name

Popular brands