Yamaha 60 Owner'S Manual Download

Page: 45 / 82

Operation

to allow operation in shallow water.

WARNING

EWM00660

●

Place the gear shift in neutral before
setting up for shallow water cruising.

●

Return the outboard motor to its normal
position as soon as the boat is back in

deeper water.

CAUTION:

ECM00260

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-

ing can result.

EMU28184

Procedure for power trim and tilt / power
tilt models

Place the gear shift lever in neutral.

Slightly tilt the outboard motor up to the

desired position using the power trim / tilt
switch.

To return the outboard motor to the nor-
mal running position, press the power
trim / tilt switch and slowly tilt the out-
board motor down.

EMU28191

Cruising in other conditions

Cruising in salt water

After operating in salt water, wash out the
cooling water passages with fresh water to

ZMU03837

Summary of Contents for 60



















































































Search results

Summary of Contents for 60

Reviews:

Related manuals for 60

Brands by name

Popular brands

Yamaha 60, Owner'S Manual

Search results

Summary of Contents for 60

Reviews:

Related manuals for 60

Brands by name

Popular brands