manualshive.com logo in svg

Yamaha 60, Owner'S Manual

Share
Download
Yamaha 60 Owner'S Manual Download Page 56

 

Maintenance

 

51

 

spilled fuel in a rag.

3.

Remove the filter element, and wash it in
solvent. Allow it to dry. Inspect the filter
element and O-ring to make sure they
are in good condition. Replace them if
necessary. If any water is found in the
fuel, the Yamaha portable fuel tank or
other fuel tanks should be checked and
cleaned.

4.

Reinstall the filter element in the cup.
Make sure the O-ring is in position in the
cup. Firmly screw the cup onto the filter
housing.

5.

Attach the filter assembly to the bracket
so that the fuel hoses are attached to the
filter assembly.

6.

Run the engine and check the filter and
lines for leaks.

 

EMU29041

 

Inspecting idling speed

WARNING

 

EWM00451 

 

●

 

Do not touch or remove electrical parts
when starting or during operation.

 

●

 

Keep hands, hair, and clothes away
from the flywheel and other rotating

 

parts while the engine is running.

CAUTION:

 

ECM00490 

 

This procedure must be performed while
the outboard motor is in the water. A
flushing attachment or test tank can be

 

used.

 

A diagnostic tachometer should be used for
this procedure. Results may vary depending
on whether testing is conducted with the
flushing attachment, in a test tank, or with the
outboard motor in the water.
1.

Start the engine and allow it to warm up
fully in neutral until it is running smooth-
ly.

NOTE:

 

Correct idling speed inspection is only possi-
ble if the engine is fully warmed up. If not
warmed up fully, the idle speed will measure
higher than normal. If you have difficulty ver-
ifying the idle speed, or the idle speed re-
quires adjustment, consult a Yamaha dealer

 

or other qualified mechanic.

2.

Verify whether the idle speed is set to
specification. For idle speed specifica-
tions, see page 42.

 

EMU29061

 

Checking water in engine oil tank

 

A translucent water drain hose is connected
from the bottom of the oil tank to the filler
neck. If water or foreign matter collects in this
hose, consult a Yamaha dealer.

 

1. Filter cup
2. Filter element
3. Filter housing
4. O-ring

ZMU02079

1

4

2

3

Summary of Contents for 60



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands