Yamaha 2009 XV250Y Owner'S Manual Download Page 23 | Manualshive

Page: 23 / 84

background image

INSTRUMENT AND CONTROL FUNCTIONS

4-7

4

or premium unleaded fuel. Use of un-
leaded fuel will extend spark plug life
and reduce maintenance costs.

EAU13581

Fuel cock

This model is equipped with a negative
pressure fuel cock. The fuel cock sup-
plies fuel from the tank to the carburetor
while also filtering it.
The fuel cock lever positions are ex-
plained as follows and shown in the il-
lustrations.

ON

With the fuel cock lever in this position,
fuel flows to the carburetor when the
engine is running. Turn the fuel cock le-
ver to this position when starting the en-
gine and riding.

RES

This indicates reserve. With the fuel
cock lever in this position, the fuel re-
serve is made available. Quickly turn
the fuel cock lever to this position if you
run out of fuel while riding, otherwise
the engine may stall and will have to be
primed (see “PRI”). After turning the
fuel cock lever to “RES”, refuel as soon
as possible and be sure to turn the fuel
cock lever back to “ON”!

1. Arrow mark positioned over “ON”

1. Arrow mark positioned over “RES”

U2UJ26E0.book Page 7 Thursday, May 22, 2008 10:21 AM

«
...
21
22
23
24
25
...
»

Summary of Contents for 2009 XV250Y





















































































Reviews:

No comments

Related manuals for 2009 XV250Y

Brand: Yamaha Pages: 860

Brand: SUOMY Pages: 84

Brand: R&G Pages: 9

Venitex BARRIER

Brand: DELTA PLUS Pages: 2

690 Enduro AUS 2010

Brand: KTM Pages: 265

Brand: Abus Pages: 18

SCARABEO 100 4T - 06-2001 PART6

Brand: APRILIA Pages: 6

Brand: Thunderbike Pages: 7

Brand: DYNATEK Pages: 2

Brand: Hudora Pages: 8

Brand: Power Fist Pages: 20

Fast Time F-10 50cc

Brand: Malaguti Pages: 151

Brand: Ruroc Pages: 51

Brand: Honda Pages: 8

Brand: hepco & becker Pages: 2

Brand: Rothewald Pages: 27

USGENERAL 97071

Brand: U.S. General Pages: 8

Brand: X-lite Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands