Yamaha 2009 XV250Y Owner'S Manual Download Page 21

Page: 21 / 84

INSTRUMENT AND CONTROL FUNCTIONS

4-5

EAU12941

Brake pedal

The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

EAU13041

Fuel tank cap

To open the fuel tank cap

Insert the key into the lock and turn it
1/4 turn clockwise. The lock will be re-
leased and the fuel tank cap can be
opened.

To close the fuel tank cap

1. Push the fuel tank cap into position

with the key inserted in the lock.

2. Turn the key counterclockwise to

the original position, and then re-
move it.

TIP

The fuel tank cap cannot be closed un-
less the key is in the lock. In addition,
the key cannot be removed if the cap is
not properly closed and locked.

WARNING

EWA11091

Make sure that the fuel tank cap is
properly closed after filling fuel.
Leaking fuel is a fire hazard.

1. Brake pedal

1. Fuel tank cap

2. Unlock.

U2UJ26E0.book Page 5 Thursday, May 22, 2008 10:21 AM

Summary of Contents for 2009 XV250Y





















































































Search results

Summary of Contents for 2009 XV250Y

Reviews:

Related manuals for 2009 XV250Y

Brands by name

Popular brands

Yamaha 2009 XV250Y, Owner'S Manual

Search results

Summary of Contents for 2009 XV250Y

Reviews:

Related manuals for 2009 XV250Y

Brands by name

Popular brands