background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-19

7

EAU22271

Adjusting the rear brake light 
switch 

The rear brake light switch, which is ac-
tivated by the brake pedal, is properly
adjusted when the brake light comes
on just before braking takes effect. If
necessary, adjust the brake light switch
as follows.
Turn the rear brake light switch adjust-
ing nut while holding the rear brake light
switch in place. To make the brake light
come on earlier, turn the adjusting nut
in direction (a). To make the brake light
come on later, turn the adjusting nut in
direction (b).

EAU22380

Checking the front brake pads 
and rear brake shoes 

The front brake pads and the rear brake
shoes must be checked for wear at the
intervals specified in the periodic main-
tenance and lubrication chart.

EAU22420

Front brake pads

Each front brake pad is provided with a
wear indicator groove, which allows
you to check the brake pad wear with-
out having to disassemble the brake.
To check the brake pad wear, check
the wear indicator groove. If a brake
pad has worn to the point that the wear

indicator groove has almost disap-
peared, have a Yamaha dealer replace
the brake pads as a set.

EAU22540

Rear brake shoes

The rear brake is provided with a wear
indicator, which allows you to check the
brake shoe wear without having to dis-
assemble the brake. To check the
brake shoe wear, check the position of
the wear indicator while applying the
brake. If a brake shoe has worn to the
point that the wear indicator reaches
the wear limit line, have a Yamaha
dealer replace the brake shoes as a
set.

1. Rear brake light switch

2. Rear brake light switch adjusting nut

1. Brake pad wear indicator groove

1. Brake shoe wear indicator
2. Brake shoe wear limit line

2

1

U2UJ26E0.book  Page 19  Thursday, May 22, 2008  10:21 AM

Summary of Contents for 2009 XV250Y





















































































Reviews: