Yamaha 2008 YZF-R1X Owner'S Manual Download

Page: 84 / 108

PERIODIC MAINTENANCE AND MINOR REPAIR

6-35

4. If the fuse immediately blows

again, have a Yamaha dealer
check the electrical system.

EAU42930

Replacing a headlight bulb

This model is equipped with quartz bulb
headlights. If a headlight bulb burns
out, replace it as follows.

To replace a high beam headlight
bulb

1. Remove panel C (if replacing the

left headlight bulb) or panel D (if re-
placing the right headlight bulb).
(See page 6-7.)

2. Disconnect the headlight coupler,

and then remove the bulb cover.

3. Unhook the headlight bulb holder,

and then remove the defective
bulb.

1. High beam headlight bulb

2. Low beam headlight bulb

1. Headlight bulb cover
2. Headlight coupler

1. Headlight bulb holder

U4C821E0.book Page 35 Tuesday, July 17, 2007 11:37 AM

Summary of Contents for 2008 YZF-R1X













































































































Search results

Summary of Contents for 2008 YZF-R1X

Reviews:

Related manuals for 2008 YZF-R1X

Brands by name

Popular brands

Yamaha 2008 YZF-R1X, Owner'S Manual

Search results

Summary of Contents for 2008 YZF-R1X

Reviews:

Related manuals for 2008 YZF-R1X

Brands by name

Popular brands