Yamaha 15D Owner'S Manual Download | Manualshive

Page: 31 / 64

background image

Operation

26

NOTE:

If the outboard motor is equipped with an en-
gine stop switch lanyard, the engine can also
be stopped by pulling the lanyard and remov-
ing the lock plate from the engine stop switch.

EMU27861

Trimming outboard motor

The trim angle of the outboard motor helps
determine the position of the bow of the boat
in the water. Correct trim angle will help im-
prove performance and fuel economy while
reducing strain on the engine. Correct trim an-
gle depends upon the combination of boat,
engine, and propeller. Correct trim is also af-
fected by variables such as the load in the
boat, sea conditions, and running speed.

WARNING

EWM00740

Excessive trim for the operating condi-
tions (either trim up or trim down) can
cause boat instability and can make steer-
ing the boat more difficult. This increases
the possibility of an accident. If the boat
begins to feel unstable or is hard to steer,
slow down and/or readjust the trim angle.

EMU27871

Adjusting trim angle for manual tilt
models

There are 4 or 5 holes provided in the clamp
bracket to adjust the outboard motor trim an-
gle.
1.

Stop the engine.

2.

Remove the trim rod from the clamp
bracket while slightly tilting the outboard
motor up.

1. Trim operating angle

1. Trim rod

ZMU02043

1

U63V17E0.book Page 26 Thursday, February 26, 2004 11:52 AM

«
...
29
30
31
32
33
...
»

Summary of Contents for 15D

































































Reviews:

No comments

Related manuals for 15D

Brand: Lantronix Pages: 10

Brand: AKM Pages: 34

Brand: Aaeon Pages: 65

Brand: Embest Pages: 91

Brand: AMPTRON Pages: 41

Brand: ST Pages: 82

Brand: Xilinx Pages: 31

Brand: JETWAY Pages: 44

Brand: Biostar Pages: 37

Brand: MATSONIC Pages: 39

Brand: Advantech Pages: 4

Brand: Advantech Pages: 98

Brand: JETWAY Pages: 48

nForce 680i LT SLI

Brand: XFX Pages: 137

Brand: Texas Instruments Pages: 18

Brand: ASROCK Pages: 2

z75a-g45 series

Brand: MSI Pages: 88

Brand: DFI Pages: 167

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands