manualshive.com logo in svg

Yamaha 15D, Owner'S Manual, Page: 53 / 64

Share
Download
Yamaha 15D Owner'S Manual Download Page 53

Trouble Recovery

48

A. Inspect spark plug and replace it with rec-
ommended type.

Q. Is high pressure fuel pump drive belt bro-
ken?
A. Have serviced by a Yamaha dealer.

Q. Is engine not responding properly to shift
lever position?
A. Have serviced by a Yamaha dealer.

Engine vibrates excessively.

Q. Is propeller damaged?
A. Have propeller repaired or replaced.

Q. Is propeller shaft damaged?
A. Have serviced by a Yamaha dealer.

Q. Are weeds or other foreign matter tangled
on propeller?
A. Remove and clean propeller.

Q. Is motor mounting bolt loose?
A. Tighten bolt.

Q. Is steering pivot loose or damaged?
A. Tighten or have serviced by a Yamaha
dealer.

EMU29431

Temporary action in emergency

EMU29440

Impact damage

WARNING

EWM00870

The outboard motor can be seriously dam-
aged by a collision while operating or
trailering. Damage could make the out-
board motor unsafe to operate.

If the outboard motor hits an object in the wa-
ter, follow the procedure below.

1.

Stop the engine immediately.

2.

Inspect the control system and all compo-
nents for damage. Also inspect the boat
for damage.

3.

Whether damage is found or not, return
to the nearest harbor slowly and careful-
ly.

4.

Have a Yamaha dealer inspect the out-
board motor before operating it again.

EMU29531

Starter will not operate

If the starter mechanism does not operate
(the engine cannot be cranked with the start-
er), the engine can be started with an emer-
gency starter rope.

WARNING

EWM01020

●

Use this procedure only in an emergen-
cy and only to return to port for repairs.

●

When the emergency starter rope is
used to start the engine, the start-in-
gear protection device does not operate.
Make sure the remote control lever is in
neutral. Otherwise the boat could unex-
pectedly start to move, which could re-
sult in an accident.

●

Attach the engine stop switch lanyard to
a secure place on your clothing, or your
arm or leg while operating.

U63V17E0.book  Page 48  Thursday, February 26, 2004  11:52 AM

Summary of Contents for 15D

































































Reviews:

No comments