Yale HSA3095, Installation Instruction, Page: 20 / 28

8
20
Configuring your system
Fine tune the operation of the control panel to your requirements; advanced programming
for PIRs and door/window contacts.
General settings menu
Pin code
To change PIN code, follow steps in Easy install
programming .
Temporary code
To change Temporary code, see steps in Easy install
programming section page 8.
Duress code
To change Duress code, see steps in Easy install
programming section page 8. This code will arm and disarm the
system as normal, but will signal a personal attack alarm to
Intamac.
Programming code
To change Programming code, see steps in Easy install
programming section page 8. This code provides access to all
the programming functions of the alarm, so it must be kept
secure.
Away entry time
Enables you to alter the entry delay time. Options available are
0 sec., 10 sec., 20 sec., up to 70 sec. in 10-sec increments.
1 Use the arrow keys to switch between options.
2 Press OK to confirm.
Note: 20 sec. is set as factory default.
Entry delay time applies only to the zone that a door contact
or PIR is installed and is set to entry point.
Away exit time
Enables you to alter the exit delay time. Options available are
0 sec., 10 sec., 20 sec. up to 70 sec. in 10-sec increments.
1 Use arrow keys to switch between options.
2 Press OK to confirm.
Note: 30 sec. is set as factory default.
Home entry time
Enables you to alter the entry delay time. Options available are
0 sec., 10 sec., 20 sec., up to 70 sec. in 10-sec increments.
1 Use the arrow keys to switch between options.
2 Press OK to confirm.
Note: 20 sec. is set as factory default.
Entry delay time applies only to the zone that a door contact
or PIR is installed and is set to entry point.
Home exit time
Selects the time delay to allow leaving the protected area of a
house when home arming. Zero (no delay to 70 seconds can be
selected in 10-second intervals.
1 Use the arrow keys to switch between options.
2 Press OK to confirm.
Note: 30 sec. is set as factory default.
Control unit siren on/off
Enables you to set the control unit siren (not external siren) to
be silent in the event of an alarm.
1 Press arrow keys to select the option.
2 Press OK to confirm.
Note: Siren ON is set as factory default. It is recommended
that the control unit siren is left on.
Away exit sound
Switches on, off and the volume of the exit countdown beeps
during the exit period when away arming.
1 Use arrow keys to switch between options.
2 Press OK to confirm
Note: Low volume is set as factory default.
Away entry sound
Switches on, off and the volume of the entry countdown
beeps during the entry period when entering the house. The
system must be disarmed during this period otherwise an alarm
will start.
1 Use arrow keys to switch between options.
2 Press OK to confirm.
Note: Low volume is set as factory default.
Home exit sound
Switches on, off and the volume of the exit countdown beeps
during the exit period when away arming.
1 Use arrow keys to switch between options.
2 Press OK to confirm
Note: Low volume is set as factory default.
Home entry sound
Switches on, off and the volume of the entry countdown
beeps during the entry period when entering the protected area
of the house when home armed. The system must be disarmed
during this period otherwise an alarm will start.
1 Use arrow keys to switch between options.
2 Press OK to confirm.
Note: Low volume is set as factory default.
Door chime
Switches on, off and the volume of the door chime in the
control unit when an entry sensor is activated.
1 Use arrow keys to switch between options.
2 Press OK to confirm.
Note: Door chime volume is set to low as factory default.
Time
Allows you to set the current time (hours and minutes).
1 Hours will flash, use arrow keys to select the hour, 24-hour
format is used.
2 Press OK to confirm the hour setting.
3 Now the minutes will flash, use arrow keys to select the
minutes.
4 Press OK to confirm.
Note: Time will have to be reset if all power to the unit is lost.
Date
Allows you to set the current date.
1 Months will flash, use arrow keys to select the month.
2 Press OK to confirm the month setting.