Yale HSA3095, Installation Instruction, Page: 17 / 28

17
Arming the system
Away arming
1 Enter your PIN code and press OK.
2 Arm and Home can be selected by using the
arrow keys, select Arm .
3 Press OK. The exit delay is displayed and counts
down from the default setting of 30 seconds. The
control unit beeps (unless exit sound has been
switched off).
4 When the time is up, the control unit sounds a
long beep. Alarm On is displayed and the
system is armed.
¥ The siren will beep once (if siren confirm has
been switched on), and the strobe will flash once
after the Exit Delay has expired.
Home arming
1 Enter your PIN code and press OK.
¥ You have a silent exit period in which to vacate
the armed area. This exit period is the same as
used when fully arming.
2 Press
t
to move the cursor down to select
Home.
3 Press OK.
¥ You can also put the system into the home mode
by using the keypad or keyfob accessory.
Stopping the exit delay
Do this by disarming the system.
1 Press .
2 Enter the PIN code.
3 Press OK.
Alarm Off will be displayed and the system
returns to disarmed mode.
Partial (by-pass) arm mode
The Partial (By-pass) Arm mode allows the user
to de-activate (by-pass) any sensors at their
discretion. This feature allows your home to be
armed yet the person inside the house can move
freely in the area where the sensor is by-passed.
1 Enter your PIN code and press OK within 10
seconds.
2 Press
6
to move the cursor down to select
Bypass .
3 Press OK .
4 All the zones are listed in zone number order.
5 Press
6
,
5
keys to select the zone to be by-
passed.
6 Press OK to confirm the selection. The selected
zone will be marked with a * character in front
of it to indicate that device is to be by-passed.
Note The zones can be toggled between
by-passed and not by-passed by pressing the
OK key repeatedly followed by the * character
appearing for By-pass setting and * character
disappearing for By-pass unsetting.
7 You can repeat Step 5 ~ Step 6 to continue
selecting the device to be by-passed.
8 After all the sensors to be by-passed have been
selected, press
to return to user menu and
the cursor stays at Arm .
9 Press OK to select Arm and to arm the
system.
Note If a censor is by-passed, then the Control
Panel will not respond to its triggering Arm mode
¥ The by-pass setting is effective for only one time,
once the system is disarmed, the by-pass setting
is cleared automatically.
¥ When a sensor is by-passed, the system can be
armed directly regardless of its fault situation (if
any). However, its fault situation is still being
monitored and will be logged and displayed
when you access the Log .
Disarming the system
1 Enter your pin code.
2 Press OK. The control unit will sound 2 short
beeps and disarm.
¥ The siren will beep twice (If siren confirm has
been switched on) and the strobe will flash from
side to side after the system has been disarmed.
Alarm activation
If a sensor is triggered when armed, or if an entry
period is left to expire, the control unit will activate
the alarm immediately, while if a Home Omit sensor
is triggered, the control unit will not respond if in
home mode.
If a 24-hour alarm, fire alarm, personal attack,
alarm tamper or medical emergency is triggered,
the control unit will activate the alarm immediately
irrespective of what armed mode the control unit is
in.
During an alarm, the control unit will sound the
siren and contact the monitoring station.
If a tamper alarm is activated when the panel is
disarmed the system will dial out, and the siren will
be on but the alarm message will not be displayed.
Stopping the alarm
A flashing ALARM! will be displayed and the
Using the system
Arm and disarm the system and practice using it. Trigger the alarm by arming the system
and opening protected doors/windows and walking past PIR s. Now is the time to show the
rest of the family how simple it is to use. The telephone features are yet to be programmed.
7