Yakar 202, Operating Manual

Page: 23 / 28

2.7
In models having chain driven thermostatic regulator (Figure
-
2/9), adjustment of the heat is done
with the numeric values taking place on it.
2.8 Elimination of extreme heat: if electricity cut off occurs, by-pass valve (Figure - 2711 ) must be
opened. In models having chain driven thermostatic regulator, bottom air-inlet duct will be closed
and combustion will be decreased.
2.9 It must be placed in the house because it also provides convection from its surrounding. It can
also be installed in a room or in the kitchen having chimney with good draft.
2.10 Central bleating Stove can not be placed in the room where people sleep. It must not be installed
outside of the house.
2.11 Chimney must be cleaned before
attaching the pipes of the stove.
2.12 Attention must be paid so that the pipes of the stove get linked to each other in good order and
one within the other.
2.13 Care must be taken so that the pipe do not enter chimney too much.
2.14
A
bad chimney draft reduces the efficiency of your Central bleating Stove and at the same time,
it can also cause results harmful for the health.
2.15 Central heating installation must be done by the authorized installer by taking installation's
connection diagram into consideration.
2.16 Water must be provided to the installation over the return pipe
from
the radiator
(Figure - 1/9).
System gets air if this is done from the expansion boiler (Figure - 1/12).
2.1 7 Grounded plug must be used and socket must be inserted to the plug.
3 - OPERATING CENTRAL HEATING STOVE
3.1 When installation becomes completed, socket must be inserted to the grounded plug, The red
color lamp from the two lamps indicates that there is electricity and the green one shows that
electricity has come to the circulation pump. You can start the operation of the circulation pump
by adjusting the pump of the thermostat
(Figure
-
1/9)
to zero degree.
3.2 Valve must be opened in order to give water to the system (Figure - 1/9) from service water line.
Valve must be closed when 1/4 of the expansion tank (Figure
-
1/12) gets filled.
3.3 By removing big yellow screw on the circulation pump, be sure that the tip of motor shaft taking
place inside turns.
If it is not
turning, shaft must be turned once with the screwdriver. Big yellow
screw is applied to its place when shaft starts to turn.
3.4 Air of the cores must be removed. Water level of expansion tank (Figure
-
1/12) must be controlled.
3.5 It is recommended to operate the circulation pump first and then to give water to the system in
order
not to
have air within the
systems of YS-02
and 202 model products. As for the problems
of airing, first the water taking place in the system is emptied. Water is given again while circulation
pump is in the working state. Water must be given to the installation from the inlet pipe of the
boiler (Figure
-
1/9).
3.6 After
becoming
sure
that there is no leakage in the
system, fuel
is loaded to the firing chamber
and then the fire is set. Pump thermostat (Figure - 1/8) is adjusted. Pump will start working when
the temperature of the water exceeds 40°C.
3.7 Temperature of the boiler's water which is determinant for the temperature of the room, is adjusted
from chain driven thermostatic regulator (Figure
-
1/8) and this regulator is optional. Chain driven
thermostatic regulator automatically controls burning speed of Central bleating Stove and it
maintains the heat of the water fixed at the adjusted temperature.
3.8 In order to obtain a good heat, the coal having 6000-7000 kcal/hour, dry and the kind to cause
less ash and by having walnut-orange size must be preferred. Big size coal
comforts
the inlet
of the air. You can also mix walnut size coal with orange size coal.
3.9 Central bleating Stove must be ignited from the top. If it is ignited from the bottom, volatile
substances taking place in the coal will be thrown out without getting burned. This means inefficient
burning and environmental pollution.