background image

FCC ID: K6630083220

IC ID: 511B-30083220

Operating Manual

5/14

Vertex Standard Co., Ltd.

3.2 INDICATORS

Channel Display

The operating channel in both transmission and reception mode.

A Indicator

Ship-ship channel in USA or Canadian mode whose counterpart in the International mode
is a public correspondence (marine operator) channel.

USA/CAN/INTL Indicator

The modes of operation for the particular channel. “USA” indicates USA mode. “CAN”
indicates Canadian mode and “INTL” indicates International mode.

H/M/L Indicator

“H” is high power. “M” is middle power and “L” is low power. Blank is a reception only
channel.

PRI Indicator

Priority Scan is activated.

SCN Indicator

Scan is activated.

TX Indicator

Indicates transmission

WX Indicator

NOAA weather channel.

MEM Indicator

The channel is in the transceiver’s scan memory.

Battery Indicator

Battery life, during transmission and reception, is as follows:

NOTE:

 The battery life indicator is accessed immediately by pressing the 

PTT

 switch. The

battery indicator should be used only as a guide in charging the 

FNB-83/FNB-V57IS

battery.

KEY Symbol Indicator

The channel is locked. All keys are disabled except for the 

H/L

PTT

 and 

LAMP

 keys

Summary of Contents for HX370S















Reviews: