Yaesu FT DX 9000MP CONTEST - DATA MANAGEMENT OPERATION, Operation Manual

Page: 163 / 180

Page 161 FT
DX
9000MP O
PERATION
M
ANUAL
MMMMM
ENU ENU
ENU ENU ENU
M M M M M
ODE ODE
ODE ODE ODE
TX AUDIO G
ROUP
146. F-PRMTRC EQ1-FREQ
Function : Selects the center frequency of the lower
range for the front panel’s parametric microphone
equalizer.
Available Values : OFF/100 ~ 700 Hz (100 Hz/step)
Default Setting : OFF
OFF: The equalizer gain and Q-factor are set
to factory defaults (flat).
100 ~ 700: You may adjust the equalizer gain and Q-
factor at this selected audio frequency via
menu items 147:
F-PRMTRC EQ1-LEVEL F-PRMTRC EQ1-LEVEL F-PRMTRC EQ1-LEVEL F-PRMTRC EQ1-LEVEL F-PRMTRC EQ1-LEVEL
and 148:
F-PRMTRC EQ1-BWTH F-PRMTRC EQ1-BWTH
F-PRMTRC EQ1-BWTH F-PRMTRC EQ1-BWTH
F-PRMTRC EQ1-BWTH
.
147. F-PRMTRC EQ1-LEVEL
Function : Adjusts the equalizer gain of the low range
of the front panel’s parametric microphone equalizer.
Available Values : –20 ~ +10
Default Setting : +5
148. F-PRMTRC EQ1-BWTH
Function : Adjusts the Q-factor of the low range of
the front panel’s parametric microphone equalizer.
Available Values : 1 ~ 10
Default Setting : 10
149. F-PRMTRC EQ2-FREQ
Function : Selects the center frequency of the middle
range for the front panel’s parametric microphone
equalizer.
Available Values : OFF/700 ~ 1500 Hz (100 Hz/step)
Default Setting : OFF
OFF: The equalizer gain and Q-factor are set
to factory defaults (flat).
700 ~ 1500: You may adjust the equalizer gain and
Q-factor at this selected audio frequency
via menu items 150:
F-PRMTRC EQ2- F-PRMTRC EQ2- F-PRMTRC EQ2- F-PRMTRC EQ2- F-PRMTRC EQ2-
LEVEL LEVEL LEVEL LEVEL LEVEL and 151: F-PRMTRC EQ2- F-PRMTRC EQ2- F-PRMTRC EQ2- F-PRMTRC EQ2- F-PRMTRC EQ2-
BWTH BWTH
BWTH BWTH BWTH .
150. F-PRMTRC EQ2-LEVEL
Function : Adjusts the equalizer gain of the middle
range of the front panel’s parametric microphone
equalizer.
Available Values : –20 ~ +10
Default Setting : +5
151. F-PRMTRC EQ2-BWTH
Function : Adjusts the Q-factor of the middle range
of the front panel’s parametric microphone equalizer.
Available Values : 1 ~ 10
Default Setting : 10
TUNING G
ROUP
139. DIAL STEP
Function : Setting of the Tuning Knob’s tuning speed
on the SSB, CW, and AM modes.
Available Values : 1 / 5 / 10 Hz
Default Setting : 10 Hz
140. DIAL CW FINE
Function : Setting of the Tuning Knob’s tuning speed
in the CW mode.
Available Values : ENABLE/DISABLE
Default Setting : DISABLE
ENABLE :Tuning in 1 Hz steps on the CW mode.
DISABLE:Tuning according to the steps determined
via menu item 138: DIAL STEP DIAL STEP DIAL STEP DIAL STEP DIAL STEP .
141. 1MHz/100kHz SELECT
Function : Selects the tuning steps for the [ CLAR/
VFO-B
] knob when the [
BAND/MHz
] button is
pressed.
Available Values : 1 MHz/100 kHz
Default Setting : 1 MHz
142. AM CH STEP
Function : Selects the tuning steps for the
microphone’s [ UP
]/[
DWN
] keys in the AM mode.
Available Values : 2.5 / 5 / 9 / 10 / 12.5 kHz
Default Setting : 5 kHz
143. FM CH STEP
Function : Selects the tuning steps for the
microphone’s [ UP
]/[
DWN
] keys in the FM mode.
Available Values : 5 / 6.25 / 10 / 12.5 / 20 / 25 kHz
Default Setting : 5 kHz
144. FM DIAL STEP
Function : Setting of the Main Tuning Knob’s tuning
speed in the FM mode.
Available Values : 10/100 Hz
Default Setting : 100 Hz
145. MY BAND
Function : Programs a band to be skipped while se-
lecting bands using the [ CLAR/VFO-B
] knob.
Available Values : 1.8 ~ 50/GEN/TRV
To program the band to be skipped, rotate the [ CLAR/
VFO-B
] knob to recall the band to be skipped while
selecting bands via the [ CLAR/VFO-B
] knob, then
press the [ ENT
] key to change this setting to “ON.”
Repeat the same procedures to cancel the setting
(skipped “off”).