Yaesu FT DX 9000MP CONTEST - DATA MANAGEMENT OPERATION, Operation Manual

Page: 108 / 180

Page 106 FT
DX
9000MP O
PERATION
M
ANUAL
S
PLIT
-F
REQUENCY
O
PERATION
CCCCC
ONVENIENT ONVENIENT
ONVENIENT ONVENIENT ONVENIENT
T T T T T
RANSMITTER RANSMITTER
RANSMITTER RANSMITTER RANSMITTER
A A A A A
CCESSORIES CCESSORIES
CCESSORIES CCESSORIES CCESSORIES
Quick Split Operation
The Quick Split feature allows you to set a one-touch offset of +5 kHz to be applied to your radio’s transmit
frequency on the Sub VFO, compared to the Main (VFO-A) frequency.
Q Q
Q Q Q
UICK UICK UICK UICK UICK
P P
P P P
OINT OINT OINT OINT OINT
:
The operating mode applied to the Sub (VFO-B)
register will be the same as that in use on the Main
(VFO-A) register.
The offset of the Sub VFO from the Main VFO is
programmed via the Menu, and is set to +5 kHz at
the factory. Other offsets may be selected, however,
using the following procedure:
1. Press the [ MNU
] key momentarily. The Menu list
will appear on the LCD display.
2. Rotate the [ MAIN Tuning Dial
] knob to select
Menu item “ GENERAL 039 QUICK SPLIT
FREQ ”.
3. Rotate the [ CLAR/VFO-B
] knob to select the de-
sired offset.
The available selections are:
–20kHz ~ 0kHz ~ +20kHz
(factory default: +5 kHz).
4. When you have completed all adjustments, press
and hold in the [ MNU
] switch for two seconds to
save the new setting and exit to normal operation.
If you only press the [
MNU
] key momentarily to
exit, any changes you performed will not be stored.
1. Start with regular transceiver operation on the Main
(VFO-A) band.
MAIN(VFO-A)
[
RX
] switch “ON” (LED glows Green)
[
TX
] switch “ON” (LED glows Red)
SUB(VFO-B)
[
RX
] switch “OFF” (LED Off)
[
TX
] switch “OFF” (LED Off)
2. Press and hold in the [ SPLIT
] switch for two sec-
onds to engage the Quick SPlit feature, and apply a
frequency 5 kHz above the Main (VFO-A) fre-
quency to the Sub (VFO-B) frequency register.
Press and hold in the [ SPLIT
] switch for two sec-
onds to increment the Main (VFO-A) frequency to
+5 kHz.
The VFO configuration will then be:
MAIN(VFO-A)
[
RX
] switch “ON” (LED glows Green)
[
TX
] switch “OFF” (LED Off)
SUB(VFO-B)
[
RX
] switch “OFF” (LED Off)
[
TX
] switch “ON” (LED glows Red)
3. Press and hold in the [ SPLIT
] switch for two sec-
onds to increment the Sub (VFO-B) frequency an-
other +5 kHz.
[CLAR/VFO-B] Knob
[MNU] Switch
[MAIN Tuning Dial] knob
MAIN(VFO-A)
[RX] Switch “ON”
(LED glows Green)
MAIN(VFO-A)
[TX] Switch “OFF”
(LED Off)
SUB(VFO-B)
[RX] Switch “OFF”
(LED Off)
SUB(VFO-B)
[TX] Switch “ON”
(LED glows Red)
[SPLIT] Switch
VDD TEMP SWR BIAS
“SPLIT” Indicator