background image

P13

Problem code and handling

For the latest information on the functionalities and settings of da Vinci Color, refer to the user manual provided or visit XYZprinting official 

website: www.xyzprinting.com. 

When a problem occurs with the printer, the service code will be displayed on the printer screen and / or the software interface. Please refer 

to this service code description form for preliminary testing.

 

Service 

Code

Symptom

Action

OO11 Print head heated for too long

please check the Flexible flat cable and reboot

OO14 Print head heated issue -- temperature exceed

OO30 Abnormal--X axis

check the cable of the motor and the sensor, and check 
the position of the sensor

OO31 Abnormal--Y axis

OO32 Abnormal--Z axis

OO50 Internal communication error -- memory error

reboot the printer

OO52 Print head memory error

replace the print head

OO55 inkjet head error

replace the inkjet head

OO56 inkjet data error

reboot the printer

You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority 

to operate the equipment. 
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These 

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses 

and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to 

radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause 

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try 

to correct the interference by one or more of the following measures: 
● Reorient or relocate the receiving antenna. 
● Increase the separation between the equipment and receiver. 
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
● Consult the dealer or an experienced radio/TV technician for help. 

XYZprinting is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by 

unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate the 

equipment. 
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful 

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC 

RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter 

must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with 

any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the   

no-collocation statement.

Federal Communications Commission (FCC) Statement

Summary of Contents for ds Vinci Color















Reviews: