background image

 

 

NEW TIPS 

Applying the following steps will lead to optimum life. 
1.

 

Set temperature to min. then turn the main power switch to the  ON  position. 

2.

 

Set temperature to 25

0

  (48

2

). 

3.

 

Coat the tinned surfaces with rosin-core solder after reaching 25

0

 

(48

2

). 

4.

 

Set to desired temperature after allowing the unit to idle at 25

0

  for 3 minutes. 

5.

 

The iron will be ready for use once it reaches the preset temperature. 

 

IMPORTANT: Remove and clean the tip daily. If a new tip is installed, remove any 
loose build up in the barrel assembly, otherwise the tip may fuse to the heating 
element or retaining barrel. 
 

                                          SMD TWEEZERS OPERATION 
For optional TWZ120 SMD Tweezers operations:

 

  Disconnect the soldering iron and change to TWZ120 Tweezers. Be sure the main 

power switch is  OFF  before preceding this operation to avoid any damage.

 

  Use only the approximately designed tips for the job to avoid unnecessary 

component damage.

 

  Gently pick up and remove components while ensuring that a vertical pick up and 

pull out motion is maintained.

 

  Use the same procedure when reconnecting the solder wand.   

 
Please note that the tweezers temperature will be lower about 5

0

  than the soldering 

iron temperature.

 

 
    Drawing of Tweezers & spares SMD tips for TWZ120 
   
 
 
 

MAINTENANCE 

TIP MAINTENANCE AND DRESSING 
Tips can be changed or replaced simply by unscrewing the knurled nut barrel 
assembly. The station must be switched off and allowed to cool before this operation 
as damage may result if the system is left on without the tip in place! 
After removing the tip, blow out any oxide dust that may have formed in the tip 
retaining area of the barrel. Be careful to avoid getting this dust in your eyes. Replace 
the tip and screw back the knurled nut barrel assembly using only firm hand pressure 
to tighten. Pliers should only be used to tighten the nut to avoid burning your fingers, 
but care should be taken not to over-tighten as this could damage the element. 
 

Summary of Contents for LF-2000










Reviews: