Xylem Sontek River Surveyor RS5 User Manual Download Page 47

Page: 47 / 149

SonTek RS5 User Manual (August 2020) 47

Measurement

Component

Variable

Action

Message

Criteria

Area

Warning

Variation in Area from the previous

transect is more than 5 percent

Warning

COV of Area is greater than 5 percent

Discharge

Warning

Variation in Total Q from the previous

transect is more than 5 percent

Warning

COV of Total Q is greater than 5

percent

Measurement

Duration

Warning

Total duration of the measurement is

less than 720 seconds. Please consider

making 2 more transects

720s

GPS

GGA

Counter /

Warning

Bad GPS-GGA samples. GPS quality is

0 or 1

Counter /

Warning

Bad GPS-GGA samples. GPS quality

changed from 4 to 2

Warning

HDOP is greater than 2

Warning

Change in altitude from the previous

sample is greater than 3 m. Check for

Multi-Path

VTG

Counter /

Warning

Bad GPS-VTG samples

Counter /

Warning

Bad GPS-VTG samples. Boat Speed is

less than 0.1 m/s

0.1m/s

Post

Processing

Composite

Tracks

Warning

System was used as track reference

Warning

BT was used as track reference

Warning

GGA was used as track reference

Warning

VTG was used as track reference

Depth

Reference

Counter /

Warning

Samples used substituted depth

reference

Track Reference Counter /

Warning

Samples used substituted track

reference

Summary of Contents for Sontek River Surveyor RS5






















































































































































Search results

Summary of Contents for Sontek River Surveyor RS5

Reviews:

Related manuals for Sontek River Surveyor RS5

Brands by name

Popular brands

Xylem Sontek River Surveyor RS5, User Manual

Search results

Summary of Contents for Sontek River Surveyor RS5

Reviews:

Related manuals for Sontek River Surveyor RS5

Brands by name

Popular brands