Xylem Flygt 5520 Installation, Operation And Maintenance Manual Download Page 37

Page: 37 / 54

Property

class

M10

M12

M16

M20

M24

M30

100

4.1 (3)

8.1 (6)

14 (10)

34 (25)

66 (49)

115 (84.8) 248 (183) 481 (355) —

—

Table 2: Steel, torque Nm (ft-lbs)

Property

class

M10

M12

M16

M20

M24

M30

8.8

2.9 (2.1)

5.7 (4.2)

9.8 (7.2)

24 (18)

47 (35)

81(60)

194 (143) 385 (285) 665 (490) 1310

(966.2)

10.9

4.0 (2.9)

8.1 (6)

14 (10)

33 (24)

65 (48)

114 (84)

277 (204) 541 (399) 935 (689) 1840

(1357)

12.9

4.9 (3.6)

9.7 (7.2)

17 (13)

40 (30)

79 (58)

136 (100) 333 (245) 649 (480) 1120

(825.1)

2210

(1630)

Hexagon screws with countersunk heads

For hexagon socket head screws with countersunk head, maximum torque for all property
classes must be 80% of the values for property class 8.8 above.

Change the oil

The following items are needed for this procedure:

• New oil plugs
• New O-rings
• Oil that should be a medical white oil of paraffin type that fulfills FDA 172.878 (a) and

viscosity close to VG32.

1. Place the pump in a horizontal position.
2. Turn the pump so that the oil hole faces downwards.
3. Unscrew the oil plug.

If the pump has a hole with the markings "oil out" it is important that this hole is used
for drainage.

WARNING:

The oil housing may be pressurized. Hold a rag over the oil plug to
prevent oil from spraying out.

WS002420A

4. Drain the pump.

Unscrew the other oil plug for easier drainage.

Maintenance

Flygt 5520 Installation, Operation, and Maintenance Manual

Summary of Contents for Flygt 5520























































Search results

Summary of Contents for Flygt 5520

Reviews:

Related manuals for Flygt 5520

Brands by name

Popular brands

Xylem Flygt 5520, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Flygt 5520

Reviews:

Related manuals for Flygt 5520

Brands by name

Popular brands