Xylem Flygt 5520 Installation, Operation And Maintenance Manual Download Page 19 | Manualshive

Page: 19 / 54

background image

When it reaches the bottom position, the pump automatically connects to the
discharge connection.

7. Secure the motor cable:

a) Fasten the permanent lifting device to the pump and to the access frame. For

example, you can use a stainless-steel lifting chain with shackles.

b) Fasten the cable to the cable holder.

Make sure that the cable cannot be sucked into the pump inlet or that it is neither
sharply bent, or pinched. Support straps are required for deep installations.

c) Connect the motor cable and the starter and monitoring equipment according to

the separate instructions.
Make sure that the impeller rotation is correct. For more information, see

impeller rotation

Clean all debris from the sump before starting the pump.

Install with S-installation

In the S-installation, the pump is transportable and intended to operate either completely
or partially submerged in the pumped liquid. The pump is equipped with a connection for
hose or pipe and stands on a base stand.
These requirements and instructions only apply when the installation is made according to
the dimensional drawing. For information about the different installation types, see Parts
List.

WS006270A

Figure 3: S-installation

1. Run the cable so that it has no sharp bends. Make sure that it is not pinched, and

cannot be sucked into the pump inlet.

2. Connect the discharge line.
3. Lower the pump into the sump.
4. Place the pump on the base and make sure it cannot fall over or sink.

Alternatively, the pump can be suspended with a lifting chain just above the sump
bottom. Make sure that the pump cannot rotate at startup or during operation.

5. Connect the motor cable and the starter and monitoring equipment according to the

separate instructions.
Make sure that the impeller rotation is correct. For more information, see

impeller rotation

Install with T/Z-installation

In the T-installation, the pump is installed in a vertical position in a dry well next to the wet
sump. These requirements and instructions only apply when the installation is made
according to the dimensional drawing.

Installation

Flygt 5520 Installation, Operation, and Maintenance Manual

17

«
...
17
18
19
20
21
...
»

Summary of Contents for Flygt 5520























































Reviews:

No comments

Related manuals for Flygt 5520

Brand: Ebsray Pages: 12

Brand: VARISCO Pages: 16

Brand: Daikin Pages: 30

Brand: Pentair Pool Products Pages: 2

Brand: Wilden Pages: 32

Brand: Flotec Pages: 12

Aqua-Pure 3MFF100

Brand: 3M Pages: 8

Brand: BLACKMER Pages: 14

Brand: Wacker Neuson Pages: 50

Brand: Enertech Pages: 40

Brand: Wayne Pages: 1

Brand: Daikin Pages: 44

Brand: YAMADA Pages: 25

Brand: Dimplex Pages: 12

Brand: Becker Pages: 6

Brand: Unico Pages: 48

Brand: EBARA Pages: 18

Brand: Walter Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands