Xylem Flygt 3060 Installation, Operation And Maintenance Manual Download Page 3

Page: 3 / 50

Table of Contents

Introduction and Safety.........................................................................................................................3

Introduction..........................................................................................................................................3
Safety terminology and symbols.......................................................................................................3
Product warranty.................................................................................................................................4

Spare parts........................................................................................................................................5

Safety.....................................................................................................................................................5
User safety............................................................................................................................................5

Hazardous liquids.............................................................................................................................6
Wash the skin and eyes....................................................................................................................6

Environmental safety...........................................................................................................................6

Transportation and Storage..................................................................................................................7

Inspect the delivery.............................................................................................................................7

Inspect the package.........................................................................................................................7
Inspect the unit..................................................................................................................................7

Transportation guidelines..................................................................................................................7

Precautions........................................................................................................................................7
Position and fastening......................................................................................................................7
Lifting..................................................................................................................................................7

Temperature ranges for transportation, handling and storage....................................................7

Handling at freezing temperature..................................................................................................7
Unit in as-delivered condition.........................................................................................................8
Lifting the unit out of liquid.............................................................................................................8

Storage guidelines..............................................................................................................................8

Storage location................................................................................................................................8
Long-term storage............................................................................................................................8

Product Description...............................................................................................................................9

Installation.............................................................................................................................................12

Install the pump.................................................................................................................................12

Make the electrical connections......................................................................................................16

Table of Contents

Flygt 3060 Installation, Operation, and Maintenance Manual

Summary of Contents for Flygt 3060



















































Search results

Summary of Contents for Flygt 3060

Reviews:

Brands by name

Popular brands

Xylem Flygt 3060, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Flygt 3060

Reviews:

Brands by name

Popular brands