manualshive.com logo in svg

Xylem Flygt 3060, Installation, Operation And Maintenance Manual

Share
Download
Xylem Flygt 3060 Installation, Operation And Maintenance Manual Download Page 11

Product Description

Products included

Pump model

Approvals

3060.390

Standard

Pump design

The pump is submersible, and driven by an electric motor.

Intended use

The product is intended for moving waste water, sludge, raw and clean water. Always
follow the limits given in 

Application limits

 (page 35). If there is a question regarding the

intended use of the equipment, please contact a local sales and service representative
before proceeding.

WARNING:

In explosive or flammable environments, only use Ex- or MSHA-approved pumps.

For information about pH, see 

Application limits

 (page 35).

The warm media (liquid) version has certain operational limitations, which are stated on a
plate on the pump. For applicability, see 

Application limits

 (page 35).

Particle size

The pump can handle liquid containing particles that correspond to the holes in the
strainer.

Number of holes

Hole dimensions

MT: 81
HT: 896

MT: 15×15 mm (0.6×0.6 in.)
HT: Diameter 5 mm (0.2 in.)

Pressure class

LT

Low head

MT

Medium head

HT

High head

Impeller type

C

Wear resistant

D

Sludge

Monitoring equipment

The following applies to the monitoring equipment of the pump:

• The stator incorporates thermal contacts connected in series that activate the alarm at

overtemperature.

• The thermal contacts open at 125°C (257°F) and close at 70°C (160°F).

Product Description

Flygt 3060 Installation, Operation, and Maintenance Manual

9

Summary of Contents for Flygt 3060



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands