manualshive.com logo in svg

Xylem Flygt 3060, Installation, Operation And Maintenance Manual

Share
Download
Xylem Flygt 3060 Installation, Operation And Maintenance Manual Download Page 12

The data plate

The data plate is a metal label located on the main body of the products. The data plate
lists key product specifications. Specially approved products also have an approval plate.

2

13

12

14

22

21
20

17 18

19

16

15

9

10

11

8

7

6

5

4

3

1

23

24

WS006257A

1.

Curve code/Propeller code

2.

Serial number, see 

Product denomination

 (page 10)

3.

Product number

4.

Country of origin

5.

Additional information

6.

Phase; type of current; frequency

7.

Rated voltage

8.

Thermal protection

9.

Thermal class

10. Rated shaft power

11. International standard

12. Degree of protection

13. Rated current

14. Rated speed

15. Maximum submergence

16. Direction of rotation: L=left, R=right

17. Duty class

18. Duty factor

19. Product weight

20. Locked rotor code letter

21. Power factor

22. Maximum ambient temperature

23. Read installation manual

24. Notified body. Only for EN-approved Ex-products

Figure 1: The data plate

Product denomination

Sales denomination

The sales denomination consists of the four-digit sales code and two letters that indicate
the hydraulic end and type of installation.

This is an example of a sales denomination, and an explanation of its parts.

1

NP 3085 

2 3

WS006265A

1.

Hydraulic part

2.

Installation type

3.

Sales code

Product Description

10

Flygt 3060 Installation, Operation, and Maintenance Manual

Summary of Contents for Flygt 3060



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands