background image

OPERATION

6

SURFACE PREPARATION

Before starting a pressure wash cleaning it is important to prepare the surface that is to be 

cleaned. This is done by clearing the area of furniture and making sure all windows and 

doors are closed tight. In addition, you should make sure all plants and trees are protected 

by a drop cloth. 

INITIAL HIGH PRESSURE RINSE

Spray the cleaning surface with water to clean off any dirt that may have collected on the 

surface. This will allow the detergent to work on the deep down dirt that has worked its way 

into the cleaning surface. Before triggering the gun, adjust the nozzle to a wide fan pattern 

and slowly adjust to the desired spray pattern. This will avoid too much concentrated spray 

to the surface which can cause damage. 

DETERGENT APPLICATION

Use only detergents formulated for pressure washes. Make sure to test the detergent in an 

inconspicuous area before use. 

1.

 Follow the label directions for mixing correct detergent to water ratio through the pressure 

washer, it is approximately 5.4% (1-19). Unscrew the top of the detergent applicator and fill 

the applicator with detergent. 

2. 

Replace the top on the applicator and remove the lance from the gun.

3. 

Attach the detergent applicator to the gun. 

4. 

Apply detergent so it thoroughly covers the cleaning surface. Apply from the bottom up.

5. 

Allow detergent to remain on the surface for a few minutes. Use a brush to lightly scrub 

heavily soiled areas. 

NEVER

 allow detergent to dry on the surface. 

6.

 Remove the detergent applicator from the gun and replace with the lance, or remove 

the applicator from the end of the lance. 

7.

 Rinse the detergent from the surface. 

NOTE:

 Flush the applicator with clean water following 

each use. 

8. 

Final Rinse: Start at the bottom and work your way upward. Make sure you thoroughly 

rinse the surface and that all detergent has been removed. 

SHUT DOWN

1. 

Turn off the motor and water supply. Squeeze the trigger gun to de-pressurize the system. 

CAUTION: NEVER 

turn the water supply off before turning the motor off. Serious damage 

could occur to both the pump and motor.

NEVER

 disconnect high pressure discharge hose from the machine while the system is 

pressurized. To de-pressurize, turn the motor of and squeeze the trigger 2-3 times. 

2. 

After each use, wipe all surfaces of the pressure washer clean with a damp cloth. 

Summary of Contents for 61032











Reviews: