Xtreme Power Conversion XPD0215SL User And Installation Manual Download Page 15

Page: 15 / 26

Xtreme Power Conversion Corporation

XPD0215SL User’s Manual

Page 15

Power Distribution Unit

Power Outlet Setup Menu (Web Page)

Name:

Define a name for the power outlet.

On/Off:

Set the power outlet to power on or off state.

Reservation:

Reserve the port for special user.

AutoPing and reboot (Power reboot If user equipment’s network is down)

Disable or enable AutoPing power reboot function. If it is enabled, the system schedules auto pings to the com-

munication equipment that is connected to the power outlet. If no response is received in a period of time (user

defined, see below) from the communication equipment, the system starts the power reboot process for the

power outlet.

Ping Ip(AutoPing (Ping) destination IP address) :

Enter an IP address of the probed communication equipment. This IP address is associated to the power outlet.

Email notify if autoping failed

Disable or enable sending email notify if autoping failed. Only available if AutoPing and reboot if on.

Reboot Duration In Seconds

Setting the reboot duration if the autping is failed or clicking “Reboot” push switch button icon. The unit is second.

Summary of Contents for XPD0215SL


























Search results

Summary of Contents for XPD0215SL

Reviews:

Related manuals for XPD0215SL

Brands by name

Popular brands

Xtreme Power Conversion XPD0215SL, User And Installation Manual

Search results

Summary of Contents for XPD0215SL

Reviews:

Related manuals for XPD0215SL

Brands by name

Popular brands