background image

16

Need help or have any questions?  Call us at 1-714-963-0329 or send us an email at [email protected]

149243 (CHB043)

Rear Tires - Spiked (1 Pair)

149248 (CHB048)

Body Clips (10)

149249 (CHB049)

3mm Nylon Insert Nuts (10)

149257

Body Posts & Support Bracket

149258

Shock Mount Set

145701

Bullet ESC

149260

Shock Ball Ends - Lower

Sorry, No

Photo Available

149255

Suspension Pin Set

149256

Rear Wheel Pins

149250 (CHB050)

4mm Nylon Insert Nuts (10)

149251 (CHB051)

Electric Motor

WARRANTY INFORMATION - PLEASE READ

Your XTM Baja Bullet 2WD electric truck is warranted against manufacturer defects in materials and workmanship for a period of 90 days from the date of purchase.
Warranty service will be provided within 90 days of the date of purchase only if you are able to provide the original (or a copy of) the original dated sales receipt.

Special Notice

The radio control system 

(except the Bullet Electronic Speed Control)

 preinstalled in your XTM Baja Bullet 2WD electric truck is manufactured and warranted by

Hitec/RCD North America.  This includes the transmitter, receiver and steering servo.  Do not return the radio system to XTM Customer Service.  It must be removed
from the truck and returned to Hitec/RCD at the address shown:

Hitec/RCD, Inc.
Attn: Customer Service Center
12115 Paine Street
Poway, CA  92064

WARRANTY SERVICE

Before returning your Baja Bullet electric truck for warranty consideration, the status of the unit must be within the guarantee as stated above.  Do not return your
truck to the place of purchase.  They are not authorized or equipped to perform warranty work on XTM Racing products.  When requesting warranty service, please
observe the following:

Crash damage will not be covered under warranty.  Do not request warranty service for a crash-damaged product.

If you are requesting warranty on anything other than just the radio control system, always send your Baja Bullet complete with the transmitter.  Please unplug and/

or remove the batteries both from the transmitter and the truck before returning it.  We like to have the truck complete so it can be thoroughly tested before returning it
to you.

If you are requesting warranty service for only the radio system 

(except the Bullet Electronic Speed Control)

 do not send the radio system or the truck to us.

Remove the radio system from the truck and return it to Hitec/RCD for warranty consideration.  See Special Notice above.

Include a note detailing the problem or service you are requesting.  Service cannot be provided without this information.  Include your daytime phone number, shipping

address and/or email address in the event we need more details pertaining to the service requested.

If your Baja Bullet is out of the warranty period you may request an estimate of services at the time you return your truck for service.  An omission of this request

implies permission for XTM Racing to service your truck at our discretion.

Include a method of payment for any service charges.

Send the unit to us by United Parcel Service, Federal Express or by Insured Mail.  Postage is non-refundable.  Send your package to:

XTM Racing Customer Service  18480 Bandilier Circle  Fountain Valley, CA  92708

Phone (714) 963-0329  Fax (714) 964-6236  Email: [email protected]

256960

4 x 8 Ball Bearings (4 Pack)

Summary of Contents for Baja Bullet

















Reviews: