Xterra TRX1000 Owner'S Manual Download Page 18

Page: 18 / 20

SERVICE CHECKLIST - DIAGNOSIS GUIDE

Before contacting us for aid, please review the following information. It may save you both time and

expense. This list includes common problems that may not be covered under the treadmill’s warranty.

1. Does the motor run after “Start” button is pressed?

2. Connector could be loose.

3. Check the cable connecting the console and controller

for proper connection.

1. If safety key switch is placed properly?

2. Is safety harness I the console connected properly?

Any connector damaged?

3. Is safety switch defective?

1. Check for proper walking belt alignment. Make sure to

lubricate belt periodically to minimize resistance.

2. Is there any bearing damage?

3. Has the motor overheated?

1. Motor is not connected properly or not connected to

the controller.

1. Check lubrication under walking belt.
Reference belt deck lubrication procedure on page 17.
2. Hold PROGRAM button for 3 seconds to reset

1. Check for proper connection between the console

and controller.

1. Controller component failure

1. Check for proper voltage input for treadmill.

Console

Showing E1

Console

Showing

LUBE

Console

Showing E0

Console

Showing E2

Console

Showing E4

Console

Showing E5

Console

Showing E6

Console

Showing E7

Console shows E1

8~10 seconds after

pressing “Start”

button.

Reminder to check

lubrication under

walking deck

Safety Switch

Malfunction

Over Current

Protection

Treadmill over loaded,

controller protection is

activated.

Improper Motor input

voltage.

Motor is not connected

properly.

Communication

disconnected between

the console and

the controller or

communication error

Controller

Malfunction

Abnormal Power

Input

Problem

Meaning

Solution

Cause

Summary of Contents for TRX1000




















Search results

Summary of Contents for TRX1000

Reviews:

Related manuals for TRX1000

Brands by name

Popular brands

Xterra TRX1000, Owner'S Manual

Search results

Summary of Contents for TRX1000

Reviews:

Related manuals for TRX1000

Brands by name

Popular brands