Coax MDU Master Bridge User
’s Guide
39
diag
-t
<mac>
-r
<mac>
EP connection
Offline Diag
, this will stop service for 10~20
secon
ds. Alike doing “
Tx Diag
”& “
Rx Diag
” test from Web.
-t: downstream SNR diagnosis(from Master to EP)
-r: upstream SNR diagnosis(from EP to Master)
<mac>
: EP MAC
<mac>
to be diagnosed
dir
Show detail file information resides in flash ROM. Include
„Working Area‟ and „Upload Area‟, refer
Figure 6
. The listed
filenames are,
„
bootcode
‟: boot loader
„
sysfw4m
‟: system firmware
„
G2C44H25M
‟: Master HCNA driver
„
G2C44H21Ep
‟: EP HCNA driver
„
diagsw
‟: diagnosis utility file
„Accompanying with file id, file version, file date, and file size.
dns
[
-s
<pri/sec> <ip>]
Display or set up DNS server setting.
-s
pri <ip>
: se
t up Primary DNS server‟s IP
-s
sec <ip>
: set up Secondary DNS serv
er‟s IP
exit
Close the Telnet console.
quit
Close the Telnet console.
ep
[
-c
<hostcnt>]
[
-n
<note>]
<mac>
Set up the
EP HomePNA Properties
related setting values.
<hostcnt>
: EP
Host Limit
setting value (0~11), default
5
<note>
: EP footnote
Note
setting value
<mac>
: designated EP MAC to configure
epreg
-m
<mac>
Add an EP profile, alike
Add EP
eprestore
-m
<mac>
Restore EP settings, alike
ReConfig EP
epstat
-m
<mac>
[
-r
]
Display remote EP port statistics of port LAN1/LAN2/HCNA.
-r: reset all port statistics counter to 0
epswc
-m
<mac>
[
-t
]
[
-u
]
[
-r
]
[
-d
]
[
-p
<lan1/lan2/hpna>
[
-l
<up/down>]
[
-s
<auto /10h /10f
/100h /100f>]
[
-f
<on/off>]]
Display or set up remote EP built-in switch Ethernet properties
-t: display EP switch settings
-u: display EP switch/port status
-r: reset EP switch
-d: reset EP switc
h‟s settings to factory default
-p: configure EP port LAN1/LAN2/HCNA
-l: link,
<up/down>
: force current port to link up or down, i.e.
enable/disable current port
-s: current port Ethernet mode setting,
<auto>
: auto-negotiation mode
<10h/10f/100h/100f>
: 10/100Mbps, half/full-duplex mode
-f: current port Ethernet flow-control setting,
<on/off>
: turn on /off flow control
epswigmp
epswqosq
epswqosrate
epswqostc
epswtagvlan
-m
<mac>
R
c
n'
efer respected
mmand
'swigmp'
,
'swqosq'
,
'swqosrate'
,
'swqostc'
,
'swtagvla
for the same functionality, but operate on remote EP with
esignated MAC address
<mac>
d
o
filter
[
-s
<set>
[
-c
<act/deact>]
[
-a
<ip>
-m
<mask>]
[
-t
<allow/deny>]
[
-w
<allow/deny>]
[
-n
<allow/deny>]
[
-p
<allow/deny>] ]
Display or set up the filter rule set, refer the section
“
Allow
Source
” for IP
<ip>
and Subnet Mask setup
<mask>
.
<set>
: filter set index, total 16 set (0~15)
<act/deact>
: activate or de-activate the rule set
<allow/deny>
: allow or deny the protocol
-t: telnet
-w: http/web
-n: snmp
-p: reply to ICMP ping
help
Display all commands with brief description
hpnareboot
Reset Master HCNA devic
e‟
Summary of Contents for XL-HCW224C
Page 6: ......