xsto CT250 Operation Manual Download Page 39

Page: 39 / 40

Name

Sketch map

Crawler

Caster

For products that are not covered by the warranty, we still serve

you enthusiastically, and only charge the cost of the parts.

6.2 Responsibility

The manufacturer is not responsible for any damage caused

to the CT250/250A/300/300A in the following cases.



Inappropriate equipment operation



Repair, dismantling or other operations of the equipment without
authorization



Operation manual is not followed



For the installation of special accessories for
CT250/250A/300/300A



Deliberately dismantle the configuration of CT250/250A/300/300A



Operation under overload conditions



Operation under low battery capacity

*If the contents of this specification are changed because improving
product quality or upgrading technical parameters, we will not give
notice. For the latest product information, please contact the supplier

Summary of Contents for CT250









































Search results

Summary of Contents for CT250

Reviews:

Related manuals for CT250

Brands by name

Popular brands

xsto CT250, Operation Manual

Search results

Summary of Contents for CT250

Reviews:

Related manuals for CT250

Brands by name

Popular brands