background image

 

 

PLEASE ENGAGE LOCAL PROFESSIONAL INSTALLER TO PERFORM 
INSTALLATION.  PLEASE  ALWAYS  FOLLOW  LOCAL  BUILDING 
CODES, ELECTRICAL CODES AND LOCAL LAWS. 

 

1.

 

Preliminary Checking: 
 

1)

 

The ceiling structure should support at least 

FOUR 

times the total weight of the 

lift and projector. Please reinforce additional supporting structure if needed.  

2)

 

Please check the overall dimensions of the lift and ensure that there is sufficient 
space above ceiling before installation. 

3)

 

100mm (4″) clearances from all surrounding structures are recommended. The 
minimum ceiling space required for the lift to install at ceiling is 1100mm (W) x 
800mm (D) x 850mm (H).  The installer must be accessible to every sides of the 
lift in order to install it. 

4)

 

Check the dimensions of the projector to be mounted within the available space.   

5)

 

Determine the projector installation position based on projection screen location 
and projector specifications. 

6)

 

Confirm that there is adequate space for installation, operation and maintenance. 

7)

 

Arrange the space for service and the access to the lift. 

8)

 

Confirm height ofceiling with maximum travel of scissor lift.  

9)

 

Physically check for any damages or loose parts on the lift. 
 
 

2.

 

Guidelines for Installation: 
 

1)

 

An  access  from  above  the  lift  with  enough  clearance  to  remove  the  top  cover 
should be provided in case of any service is required. 

2)

 

Installer  must  ensure  that  all  fasteners  support  have  adequate  strength  to 
securely support the scissor lift and projector.  

3)

 

The lift must be installed in level from front-to-back and side-to-side. 

4)

 

Make  sure  that  the  liftis  level  in  all  directions  and  weight  should  be  shared 
equally by all four threaded mounting rods. 

5)

 

Bottom of the lift must be unobstructed after installation.  

 

 

3.

 

Installation on Ceiling: 

Summary of Contents for SC60























Reviews: