manualshive.com logo in svg

Xilinx LogiCORE IP v1.02a, Product Manual, Page: 20 / 57

Share
Download
Xilinx LogiCORE IP v1.02a Product Manual Download Page 20

I/O Module v1.02a

www.xilinx.com

20

PG052 October 16, 2012

Product Specification

Register Space

Interrupt Acknowledge Register (IRQ_ACK)

This register is used as a command register for clearing individual interrupts in IRQ_STATUS 

and IRQ_PENDING registers. All bits set to 1 clear the corresponding bits in the IRQ_STATUS 

and IRQ_PENDING registers. The register is write-only.

 

 

Interrupt Mode Register (IRQ_MODE)

This register is used to define which interrupts use fast interrupt mode. All bits set to 1 use 

fast interrupt mode. The register is write-only. The register is only implemented when fast 

interrupt mode is enabled, by setting C_INTC_HAS_FAST to 1.

Table 2-24:

Interrupt Acknowledge Register (IRQ_ACK)

IRQ_ACK

31

0

Table 2-25:

Interrupt Acknowledge Register Bit Definitions

Bit(s)

Name

Core

Access

Reset
Value

Description

31:0

IRQ_ACK

W

0

All bit position written with 1 will clear corresponding bits in 

both the IRQ_STATUS and the IRQ_PENDING registers

Table 2-26:

Interrupt Mode Register (IRQ_MODE)

IRQ_MODE

31

0

Table 2-27:

Interrupt Mode Register Bit Definitions

Bit(s)

Name

Core

Access

Reset
Value

Description

31:0

IRQ_MODE

W

0

All bit positions written with 1 use fast interrupt mode

Summary of Contents for LogiCORE IP v1.02a


























































Reviews:

No comments