Xilinx LogiCORE IP v1.02a Product Manual Download Page 19

Page: 19 / 57

I/O Module v1.02a

www.xilinx.com

PG052 October 16, 2012

Product Specification

Register Space

Interrupt Enable Register (IRQ_ENABLE)

The Interrupt Enable Register enables assertion of the I/O Module interrupt output signal

INTC_IRQ by individual interrupt sources. The contents of this register are also used to mask

the value of the IRQ_STATUS register when registering enabled interrupts in the

IRQ_PENDING register.

Table 2-22:

Interrupt Enable Register (IRQ_ENABLE)

Reserved

INTC_Interrupt

Reserved

Internal Interrupts

C_INTC_E16 C_INTC_E15

16 15

11 10

Table 2-23:

Interrupt Enable Register Bit Definitions

Bit(s)

Name

Core

Access

Reset

Value

Description

31:[C_INTC_E16]

Reserved

[C_INTC_E15]:16 INTC_Interrupt

Enable I/O Module external interrupt input

signal

INTC_Interrupt(16-C_INTC_EXT_INTR)

Reserved

GPI4

GPI4 changed

GPI3

GPI3 changed

GPI2

GPI2 changed

GPI1

GPI1 changed

FIT4

FIT4 interrupt enabled

FIT3

FIT3 interrupt enabled

FIT2

FIT2 interrupt enabled

FIT1

FIT1 interrupt enabled

PIT4

PIT4 interrupt enabled

PIT3

PIT3 interrupt enabled

PIT2

PIT2 interrupt enabled

PIT1

PIT1 interrupt enabled

UART_RX

UART Received Data interrupt enabled

UART_TX

UART Transmitted Data interrupt enabled

UART_ERR

UART Error interrupt enabled

Summary of Contents for LogiCORE IP v1.02a


























































Search results

Summary of Contents for LogiCORE IP v1.02a

Reviews:

Xilinx LogiCORE IP v1.02a, Product Manual, Page: 19 / 57

Search results

Summary of Contents for LogiCORE IP v1.02a

Reviews: