Xilinx KCU1250 10GBASE-KR User Manual Download

Page: 87 / 91

10GBASE-KR Ethernet TRD

UG1058 (v2017.1) April 19, 2017

www.xilinx.com

Appendix C:

User-Space Registers

Traffic Generator—Monitor Channel 1

Table C-8:

Design Version Register (0x4AA1_0000)

Bit Position

Mode

Default Value

Description

4:0

Read Only

4’h2

Ethernet reference design 2.

14:5

12’h141

Software version: Indicates the Vivado® Design Suite version

used when developing this reference design. For example,

Vivado Design Suite 2014.1 is indicated by 141.

31:16

16’h1250

Target Board. KCU1250 board.

Table C-9:

Ethernet Performance Monitor, Transmit Payload Byte Count Register (0x4AA1_0004)

Bit Position

Mode

Default Value

Description

1:0

Read Only

Sample count. Increments once every second.

31:2

Transmit payload byte count. This field contains the interface

utilization count for active beats (tx_axis_tready = 1 and

tx_axis_tvalid = 1) on channel 1 10G Ethernet MAC AXI4-Stream

interface for transmit.

Table C-10:

Ethernet Performance Monitor, Transmit Packet Count Register (0x4AA1_0008)

Bit Position

Mode

Default Value

Description

1:0

Read Only

Sample count. Increments once every second.

31:2

Transmit packet count. This field contains the count for the

event when there is an active beat on channel 1 10G Ethernet

MAC AXI4-Stream interface and end of packet (tx_axis_tlast) is

asserted for transmit.

Table C-11:

Ethernet Performance Monitor, Received Payload Byte Count Register (0x4AA1_000C)

Bit Position

Mode

Default Value

Description

1:0

Read Only

Sample count. Increments once every second.

31:2

Receive payload byte count. This field contains the interface

utilization count for active beats (rx_axis_tready = 1 and

rx_axis_tvalid = 1) on channel 1 - 10G Ethernet MAC

AXI4-Stream interface for receive.

Table C-12:

Ethernet Performance Monitor, Received Packet Count Register (0x4AA1_0010)

Bit Position

Mode

Default Value

Description

1:0

Read Only

Sample count. Increments once every second.

31:2

Receive packet count. This field contains the count for the event

when there is an active beat on channel 1 10G Ethernet MAC

AXI4-Stream interface and end of packet (rx_axis_tlast) is

asserted for receive.

Send Feedback

Summary of Contents for KCU1250 10GBASE-KR




























































































Search results

Summary of Contents for KCU1250 10GBASE-KR

Reviews:

Related manuals for KCU1250 10GBASE-KR

Brands by name

Popular brands

Xilinx KCU1250 10GBASE-KR, User Manual

Search results

Summary of Contents for KCU1250 10GBASE-KR

Reviews:

Related manuals for KCU1250 10GBASE-KR

Brands by name

Popular brands